PIC16F883-I/SP Microchip Technology, PIC16F883-I/SP Datasheet - Page 27

• Manufacturer Part Number: PIC16F883-I/SP
• Description: IC PIC MCU FLASH 4KX14 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F883-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 24
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: MSSP/EUSART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM164120-3
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP1631RD-MCC2 - REFERENCE DESIGN MCP1631HVDVA18XP280 - DEVICE ADAPTER 18F2220 PDIP 28LD
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

4.0
The PIC16F88X has several Configuration bits. These
bits can be programmed (reads ‘0’), or left unchanged
(reads ‘1’), to select various device configurations.
4.1
The LVP bit in the Configuration Word 1 register
enables low-voltage ICSP programming. The LVP bit
defaults to a ‘1’ following an erase. If Low-Voltage Pro-
gramming mode is not used, the LVP bit can be pro-
grammed to a ‘0’ and RB3/PGM becomes a digital I/O
pin. However, the LVP bit may only be programmed by
entering the High-Voltage ICSP mode, where MCLR/
V
to a ‘0’, only the High-Voltage ICSP mode is available
and only the High-Voltage ICSP mode can be used to
program the device.
 2009 Microchip Technology Inc.
PP
Note 1: The normal High-Voltage ICSP mode is
is raised to V
2: While in Low-Voltage ICSP mode, the
3: If the device Master Clear is disabled,
CONFIGURATION WORD
Low-Voltage Programming (LVP)
Bit
a) disable
b) make certain that RB3/PGM is held low
always available, regardless of the state
of the LVP bit, by applying V
MCLR/V
RB3 pin can no longer be used as a
general purpose I/O.
verify that either of the following is done to
ensure proper entry into ICSP mode:
(Config Word 1<12> = 0); or
during entry into ICSP.
IHH
. Once the LVP bit is programmed
PP
Low-Voltage
pin.
Programming
IHH
to the
PIC16F88X
DS41287D-page 27