DSPIC33FJ64GP310T-I/PF Microchip Technology, DSPIC33FJ64GP310T-I/PF Datasheet - Page 170

• Manufacturer Part Number: DSPIC33FJ64GP310T-I/PF
• Description: IC DSPIC MCU/DSP 64K 100TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ64GP310T-I/PF

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 32x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• For Use With: DM300024 - KIT DEMO DSPICDEM 1.1DV164033 - KIT START EXPLORER 16 MPLAB ICD2MA330012 - MODULE DSPIC33 100P TO 84QFPMA330011 - MODULE DSPIC33 100P TO 100QFPDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164323 - MODULE SKT FOR 100TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

dsPIC33FJXXXGPX06/X08/X10
15.1
Configure the Output Compare modes by setting the
appropriate Output Compare Mode (OCM<2:0>) bits in
the Output Compare Control (OCxCON<2:0>) register.
Table 15-1 lists the different bit settings for the Output
Compare modes. Figure 15-2 illustrates the output
compare operation for various modes. The user
TABLE 15-1:
FIGURE 15-2:
DS70286C-page 168
OCM<2:0>
000
001
010
011
100
101
110
111
Active-High One-Shot
Active-Low One-Shot
(OCM = 110 or 111)
Delayed One-Shot
Continuous Pulse
Output Compare Modes
(OCM = 001)
(OCM = 010)
(OCM = 011)
(OCM = 100)
(OCM = 101)
Module Disabled
Active-Low One-Shot
Active-High One-Shot
Toggle
Delayed One-Shot
Continuous Pulse
PWM without Fault Protection
PWM with Fault Protection
OUTPUT COMPARE MODES
Toggle
TMRy
PWM
OUTPUT COMPARE OPERATION
OCxRS
OCxR
Mode
Output Compare
Mode Enabled
Current output is maintained
Controlled by GPIO register
‘1’, if OCxR is non-zero
‘1’, if OCxR is non-zero
OCx Pin Initial State
‘0’, if OCxR is zero
‘0’, if OCxR is zero
Timer is Reset on
Period Match
0
1
0
0
application must disable the associated timer when
writing to the Output Compare Control registers to
avoid malfunctions.
Note:
See Section 13. “Output Compare”
(DS70209) in the “dsPIC33F Family Ref-
erence Manual” for OCxR and OCxRS
register restrictions.
OCx rising edge
OCx falling edge
OCx rising and falling edge
OCx falling edge
OCx falling edge
No interrupt
OCFA falling edge for OC1 to OC4
OCx Interrupt Generation
© 2009 Microchip Technology Inc.
—