PIC24FJ128GB206-I/PT Microchip Technology, PIC24FJ128GB206-I/PT Datasheet - Page 6

• Manufacturer Part Number: PIC24FJ128GB206-I/PT
• Description: MCU PIC 16BIT FLASH USB 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ128GB206-I/PT

• Core Size: 16-Bit
• Program Memory Size: 128KB (43K x 24)
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 52
• Program Memory Type: FLASH
• Ram Size: 96K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC24
• No. Of I/o's: 52
• Ram Memory Size: 96KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Interface: I2C, SPI, UART, USB
• Embedded Interface Type: I2C, SPI, UART, USB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC24FJ256GB210 FAMILY
2. Module: Guidelines for Getting Started
Section 2.4 Voltage Regulator Pins (ENVREG and
V
section. The entire text follows:
2.4
The on-chip voltage regulator enable pin (ENVREG)
must always be connected directly to a supply voltage.
Refer to Section 26.2 “On-Chip Voltage Regulator”
for details on connecting and using the on-chip
regulator.
When the regulator is enabled, a low-ESR (< 5Ω)
capacitor is required on the V
voltage regulator output voltage. The V
be connected to V
connected to ground. The type can be ceramic or
tantalum. Suitable examples of capacitors are shown in
Table
be used.
Designers may use
equivalence of candidate devices.
TABLE 2-1
DS80504C-page 6
CAP
Panasonic
Panasonic
Murata
Murata
Make
) has been replaced with a new and more detailed
TDK
TDK
2-1. Capacitors with equivalent specifications can
Voltage Regulator Pins (ENVREG
and V
with 16-Bit Microcontrollers
CAP
DD
SUITABLE CAPACITOR EQUIVALENTS
GRM32DR71C106KA01L
GRM31CR61C106KC31L
and must use a capacitor of 10 µF
)
C3216X7R1C106K
C3216X5R1C106K
ECJ-3YX1C106K
ECJ-4YB1C106K
Figure 2-3
Part #
CAP
pin to stabilize the
to evaluate ESR
CAP
pin must not
Capacitance
Nominal
10 µF
10 µF
10 µF
10 µF
10 µF
10 µF
The placement of this capacitor should be close to
V
exceed 0.25 inch (6 mm). Refer to Section 29.0
“Electrical
information.
FIGURE 2-3
.
CAP
Base Tolerance Rated Voltage Temp. Range
0.001
Note:
0.01
. It is recommended that the trace length not
0.1
10
1
0.01
±10%
±10%
±10%
±10%
±10%
±10%
Typical data measurement at 25°C, 0V DC bias.
0.1
Characteristics”
Frequency (MHz)
FREQUENCY vs. ESR
PERFORMANCE FOR
SUGGESTED V
1
 2011 Microchip Technology Inc.
16V
16V
16V
16V
16V
16V
10
100
for
-55 to 125ºC
-55 to 125ºC
-55 to 125ºC
-55 to 85ºC
-55 to 85ºC
-55 to 85ºC
CAP
1000 10,000
additional