STM8L152K4T6 STMicroelectronics, STM8L152K4T6 Datasheet - Page 105

• Manufacturer Part Number: STM8L152K4T6
• Description: IC MCU 8BIT 16KB FLASH 32LQFP
• Manufacturer: STMicroelectronics
• Series: STM8L EnergyLiter

Specifications of STM8L152K4T6

• Core Processor: STM8
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, IR, LCD, POR, PWM, WDT
• Number Of I /o: 29
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 21x12b, D/A 1x12
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: STM8L15x
• Core: STM8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 29
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWSTM8
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 21 Channel
• On-chip Dac: 12 bit, 1 Channel
• For Use With: 497-10594 - DEM FOR STM8L15X LOW PWR MODES
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-10511

STM8L151xx, STM8L152xx
Figure 38. ADC1 accuracy characteristics
Figure 39. Typical connection diagram using the ADC
1. Refer to
2. C
General PCB design guidelines
Power supply decoupling should be performed as shown in
depending on whether V
capacitors should be used. They should be placed as close as possible to the chip.
4095
4094
4093
pad capacitance (roughly 7 pF). A high C
this, f
7
6
5
4
3
2
1
parasitic
0
V
SSA
[1LSB
ADC
1
Table 53
represents the capacitance of the PCB (dependent on soldering and PCB layout quality) plus the
E
should be reduced.
IDEAL
O
2
=
V
4096
3
for the values of R
REF+
4
(or
REF+
V
5
1 LSB
4096
DDA
E
6
T
depending on package)]
IDEAL
is connected to V
Doc ID 15962 Rev 6
E
AIN
7
L
(2)
and C
parasitic
E
D
ADC
4093 4094 4095 4096
(3)
value will downgrade conversion accuracy. To remedy
.
(1)
DDA
E
G
or not. Good quality ceramic 10 nF
V
DDA
(1) Example of an actual transfer curve
(2) The ideal transfer curve
(3) End point correlation line
E
between the actual and the ideal transfer curves.
E
transition and the first ideal one.
E
transition and the last actual one.
E
between actual steps and the ideal one.
E
between any actual transition and the end point
correlation line.
T
O
G
D
L
=Total Unadjusted Error: maximum deviation
=Integral Linearity Error: maximum deviation
=Differential Linearity Error: maximum deviation
=Offset Error: deviation between the first actual
=Gain Error: deviation between the last ideal
Figure 40
Electrical parameters
or
Figure
41,
105/122
ai14395b