C8051F335-GMR Silicon Laboratories Inc, C8051F335-GMR Datasheet - Page 166

• Manufacturer Part Number: C8051F335-GMR
• Description: IC 8051 MCU 2K FLASH 20MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F33xr

Specifications of C8051F335-GMR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 17
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-QFN
• For Use With: 336-1451 - ADAPTER PROGRAM TOOLSTICK F330
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -

C8051F330/1/2/3/4/5
*Note: In slave mode, data on MOSI is sampled in the center of each data bit. In master mode, data on MISO is
170
Bit 7:
Bit 6:
Bit 5:
Bit 4:
Bit 3:
Bit 2:
Bit 1:
Bit 0:
SPIBSY
Bit7
sampled one SYSCLK before the end of each data bit, to provide maximum settling time for the slave device.
See Table 17.1 for timing parameters.
R
SPIBSY: SPI Busy (read only).
This bit is set to logic 1 when a SPI transfer is in progress (Master or slave Mode).
MSTEN: Master Mode Enable.
0: Disable master mode. Operate in slave mode.
1: Enable master mode. Operate as a master.
CKPHA: SPI0 Clock Phase.
This bit controls the SPI0 clock phase.
0: Data centered on first edge of SCK period.
1: Data centered on second edge of SCK period.
CKPOL: SPI0 Clock Polarity.
This bit controls the SPI0 clock polarity.
0: SCK line low in idle state.
1: SCK line high in idle state.
SLVSEL: Slave Selected Flag (read only).
This bit is set to logic 1 whenever the NSS pin is low indicating SPI0 is the selected slave. It
is cleared to logic 0 when NSS is high (slave not selected). This bit does not indicate the
instantaneous value at the NSS pin, but rather a de-glitched version of the pin input.
NSSIN: NSS Instantaneous Pin Input (read only).
This bit mimics the instantaneous value that is present on the NSS port pin at the time that
the register is read. This input is not de-glitched.
SRMT: Shift Register Empty (Valid in Slave Mode, read only).
This bit will be set to logic 1 when all data has been transferred in/out of the shift register,
and there is no new information available to read from the transmit buffer or write to the
receive buffer. It returns to logic 0 when a data byte is transferred to the shift register from
the transmit buffer or by a transition on SCK.
NOTE: SRMT = 1 when in Master Mode.
RXBMT: Receive Buffer Empty (Valid in Slave Mode, read only).
This bit will be set to logic 1 when the receive buffer has been read and contains no new
information. If there is new information available in the receive buffer that has not been read,
this bit will return to logic 0.
NOTE: RXBMT = 1 when in Master Mode.
MSTEN
R/W
Bit6
SFR Definition 17.1. SPI0CFG: SPI0 Configuration
CKPHA
R/W
Bit5
CKPOL
R/W
Bit4
SLVSEL
Rev. 1.7
Bit3
R
*
NSSIN
*
Bit2
R
SRMT
Bit1
R
SFR Address: 0xA1
RXBMT
Bit0
R
Reset Value
00000111