C8051F541-IM Silicon Laboratories Inc, C8051F541-IM Datasheet - Page 253

• Manufacturer Part Number: C8051F541-IM
• Description: IC 8051 MCU 16K FLASH 32-QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F54xr

Specifications of C8051F541-IM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 32-QFN
• Mfg Application Notes: LIN Bootloader AppNote
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.25 V
• Data Converters: A/D 25x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: C8051F5x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 25
• Operating Supply Voltage: 1.8 V to 5.25 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F540DK
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1672 - BOARD PROTOTYPE W/C8051F540336-1669 - KIT DEVELOPMENT FOR C8051F540
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1673-5

24.3.1. Edge-triggered Capture Mode
In this mode, a valid transition on the CEXn pin causes the PCA to capture the value of the PCA coun-
ter/timer and load it into the corresponding module's 16-bit capture/compare register (PCA0CPLn and
PCA0CPHn). The CAPPn and CAPNn bits in the PCA0CPMn register are used to select the type of transi-
tion that triggers the capture: low-to-high transition (positive edge), high-to-low transition (negative edge),
or either transition (positive or negative edge). When a capture occurs, the Capture/Compare Flag (CCFn)
in PCA0CN is set to logic 1. An interrupt request is generated if the CCFn interrupt for that module is
enabled. The CCFn bit is not automatically cleared by hardware when the CPU vectors to the interrupt ser-
vice routine, and must be cleared by software. If both CAPPn and CAPNn bits are set to logic 1, then the
state of the Port pin associated with CEXn can be read directly to determine whether a rising-edge or fall-
ing-edge caused the capture.
Bit Number
Capture triggered by positive edge on CEXn
Capture triggered by negative edge on CEXn
Capture triggered by any transition on CEXn
Software Timer
High Speed Output
Frequency Output
8-Bit Pulse Width Modulator (Note 7)
9-Bit Pulse Width Modulator (Note 7)
10-Bit Pulse Width Modulator (Note 7)
11-Bit Pulse Width Modulator (Note 7)
16-Bit Pulse Width Modulator
Notes:
1. X = Don’t Care (no functional difference for individual module if 1 or 0).
2. A = 1 to enable interrupts for this module (PCA interrupt triggered on CCFn set to 1).
3. B = 1 to enable 8th, 9th, 10th or 11th bit overflow interrupt (Depends on setting of CLSEL[1:0]).
4. C = When set to 0, the digital comparator is off. For high speed and frequency output modes, the
5. D = Selects whether the Capture/Compare register (0) or the Auto-Reload register (1) for the associated
6. E = When set to 1, a match event will cause the CCFn flag for the associated channel to be set.
7. All modules set to 8, 9, 10 or 11-bit PWM mode use the same cycle length setting.
associated pin will not toggle. In any of the PWM modes, this generates a 0% duty cycle (output = 0).
channel is accessed via addresses PCA0CPHn and PCA0CPLn.
Operational Mode
Table 24.2. PCA0CPM and PCA0PWM Bit Settings for
PCA Capture/Compare Modules
Rev. 1.1
X X 1 0 0 0 0 A 0 X B XXX
X X 0 1 0 0 0 A 0 X B XXX
X X 1 1 0 0 0 A 0 X B XXX
X C 0 0 1 0 0 A 0 X B XXX
X C 0 0 1 1 0 A 0 X B XXX
X C 0 0 0 1 1 A 0 X B XXX
7 6 5 4 3 2 1 0 7 6 5
0 C 0 0 E 0 1 A 0 X B XXX
0 C 0 0 E 0 1 A D X B XXX
0 C 0 0 E 0 1 A D X B XXX
0 C 0 0 E 0 1 A D X B XXX
1 C 0 0 E 0 1 A 0 X B XXX
PCA0CPMn
C8051F54x
PCA0PWM
4–2 1–0
XX
XX
XX
XX
XX
XX
XX
00
01
10
11
253