DS80C323-ECD+ Maxim Integrated Products, DS80C323-ECD+ Datasheet - Page 12

• Manufacturer Part Number: DS80C323-ECD+
• Description: IC MCU HI SPEED 18MHZ 44-TQFP
• Manufacturer: Maxim Integrated Products
• Series: 80Cr

Specifications of DS80C323-ECD+

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 18MHz
• Connectivity: EBI/EMI, SIO, UART/USART
• Peripherals: Power-Fail Reset, WDT
• Number Of I /o: 32
• Program Memory Type: ROMless
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: 80C
• Core: 8051
• Data Bus Width: 8 bit
• Program Memory Size: 64 KB
• Data Ram Size: 64 KB
• Interface Type: UART
• Maximum Clock Frequency: 18 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: 0 C
• Package: 44TQFP
• Device Core: 8051
• Family Name: 80C
• Maximum Speed: 18 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: DS80C323+ECD; DS80C323+ECD

STRETCH MEMORY CYCLE
The DS80C320/DS80C323 allow the application software to adjust the speed of data memory access. The
microcontroller is capable of performing the MOVX in as little as two instruction cycles. However, this
value can be stretched as needed so that both fast memory and slow memory or peripherals can be
accessed with no glue logic. Even in high-speed systems, it may not be necessary or desirable to perform
data memory access at full speed. In addition, there are a variety of memory-mapped peripherals such as
LCD displays or UARTs that are not fast.
The Stretch MOVX is controlled by the Clock Control Register at SFR location 8Eh as described below.
This allows the user to select a stretch value between 0 and 7. A Stretch of 0 will result in a two-machine
cycle MOVX. A Stretch of 7 will result in a MOVX of nine machine cycles. Software can dynamically
change this value depending on the particular memory or peripheral.
On reset, the Stretch value will default to 1, resulting in a three-cycle MOVX. Therefore, RAM access
will not be performed at full speed. This is a convenience to existing designs that may not have fast RAM
in place. When maximum speed is desired, the software should select a Stretch value of 0. When using
very slow RAM or peripherals, a larger stretch value can be selected. Note that this affects data memory
only and the only way to slow program memory (ROM) access is to use a slower crystal.
Using a Stretch value between 1 and 7 causes the microcontroller to stretch the read/write strobe and all
related timing. This results in a wider read/write strobe allowing more time for memory/peripherals to
respond. The timing of the variable speed MOVX is shown in the Electrical Specifications section. Note
that full speed access is not the reset default case. Table 2 shows the resulting strobe widths for each
Stretch value. The memory stretch is implemented using the Clock Control special-function register at
SFR location 8Eh. The stretch value is selected using bits CKCON.2–0. In the table, these bits are
referred to as M2 through M0. The first stretch (default) allows the use of common 120ns or 150ns RAMs
without dramatically lengthening the memory access.
Table 2. Data Memory Cycle Stretch Values
MD2
0
0
0
0
1
1
1
1
CKCON.2–0
MD1
0
0
1
1
0
0
1
1
MD0
0
1
0
1
0
1
0
1
MEMORY
3 (default)
CYCLES
2
4
5
6
7
8
9
WIDTH IN CLOCKS
RD
DS80C320/DS80C323 High-Speed/Low-Power Microcontrollers
or
12 of 38
WR
12
16
20
24
28
2
4
8
STROBE
STROBE WIDTH
TIME AT 25MHz
1120
(ns)
160
320
480
640
800
960
80