PIC16F76T-E/SO Microchip Technology, PIC16F76T-E/SO Datasheet

IC MCU FLASH 8KX14 A/D 28SOIC

PIC16F76T-E/SO

Manufacturer Part Number
PIC16F76T-E/SO
Description
IC MCU FLASH 8KX14 A/D 28SOIC
Manufacturer
Microchip Technology
Series
PIC® 16Fr

Specifications of PIC16F76T-E/SO

Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
22
Program Memory Size
14KB (8K x 14)
Program Memory Type
FLASH
Ram Size
368 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Data Converters
A/D 5x8b
Oscillator Type
External
Operating Temperature
-40°C ~ 125°C
Package / Case
28-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
PIC16F76TE/SO
The PIC16F73/74/76/77 Rev. B1 parts you have
received conform functionally to the Device Data Sheet
(DS30325B), except for the anomalies described
below.
All the problems listed here will be addressed in future
revisions of the PIC16F73/74/76/77 silicon.
1. Module: Timer1
 2003 Microchip Technology Inc.
When Timer1 is running in Asynchronous mode
and then disabled, data in the Timer1 register
(TMR1) may become corrupted. Corruption occurs
when the timer enable is turned off at the same
instant that a ripple carry occurs in the timer
module.
This issue only occurs in asynchronous operation.
In synchronous operation, the relevant signals are
latched with the CPU clock and the problem
condition does not arise.
Revision C silicon will correct this issue.
Work around
When Timer1 is configured to operate as an asyn-
chronous counter, care must be taken that there is
no incoming pulse while the module is being
turned off. If an incoming pulse arrives while
Timer1 is being turned off, the value of register
TMR1 may become corrupted.
If an application requires that Timer1 be turned off,
and if it is possible that Timer1 may receive an
incoming pulse while being turned off, synchronize
the external clock first by clearing the T1SYNC bit
of register T1CON (T1CON<2>). Please note,
however, that this may cause Timer1 to miss up to
one count.
Date Codes that pertain to this issue:
PIC16F73/74
PIC16F76/77
PIC16F73/74/76/77 Rev. B1 Silicon/Data Sheet Errata
0219 and earlier
0303 and earlier
PIC16F73/74/76/77
2. Module: CCP (Compare Mode)
The output of the CCP module in Compare mode
may become inverted when the mode of the mod-
ule is changed from Compare/Clear on Match
(CCPxM<3:0> = 1001) to Compare/Set on Match
(CCPxM<3:0> = 1000). This may occur as a result
of any operation that selectively clears bit
CCPxM0, such as a BCF instruction.
When this condition occurs, the output becomes
inverted when the instruction is executed. It will
remain
operations until the module is reset.
Revision C silicon will correct this issue.
Work around
Do not selectively clear bit CCPxM0 to select the
Compare/Set on Match mode. Instead, clear the
entire CCPxCON register, which resets the mod-
ule. Follow this with an instruction to set CCPxM3
(CCPxCON<3>), which selects the Set on Match
mode.
Date Codes that pertain to this issue:
PIC16F73/74
PIC16F76/77
inverted
for
all
0219 and earlier
0303 and earlier
following
DS80099G-page 1
compare

Related parts for PIC16F76T-E/SO

PIC16F76T-E/SO Summary of contents

Page 1

... Date Codes that pertain to this issue: PIC16F73/74 0219 and earlier PIC16F76/77 0303 and earlier  2003 Microchip Technology Inc. PIC16F73/74/76/77 2. Module: CCP (Compare Mode) The output of the CCP module in Compare mode may become inverted when the mode of the mod- ule is changed from Compare/Clear on Match (CCPxM< ...

Page 2

... XT Oscillator mode. DS80099G-page 2 FIGURE Date Codes that pertain to this issue: PIC16F73/74 , resonator fre- PIC16F76/77 CRYSTAL/CERAMIC RESONATOR OPERATION (HS OSC CONFIGURATION) OSC1 To Internal Logic RF XTAL OSC2 SLEEP Rs PIC16F7X 0219 and earlier 0303 and earlier  2003 Microchip Technology Inc. ...

Page 3

... Date Codes that pertain to this issue: All. TABLE 1: DC SPECIFICATION CHANGES FROM DATA SHEET Param Characteristic/ Sym. No. Device D010A I Supply Current DD PIC16LF73/74/76/77  2003 Microchip Technology Inc. PIC16F73/74/76/77 of 3.0V DD Data Sheet New Specification Specification Min Typ Max Min Typ Max — ...

Page 4

... TTL = TTL input DS80099G-page 4 I/O/P Buffer Type Type ST I/O Digital I/O – Open drain when configured as output. I Timer0 external clock input. TTL I/O Digital I/O. I SPI slave select input. I Analog input 4. I/O = input/output ST = Schmitt Trigger input Description P = power  2003 Microchip Technology Inc. ...

Page 5

... RB3 PGM . . .  2003 Microchip Technology Inc. PIC16F73/74/76/77 References to the PGM function in the Pin Diagrams on pages 2 and 3, and Figures 1-1 and 1-2 (pages 6 and 7) in the Data Sheet have also been removed. A reference to the PGM function listed in the Data Sheet Index has also been removed. ...

Page 6

... For the sake of completeness also noted that the package designation “MLF” is now replaced by “QFN” in all occurrences through- out the Device Data Sheet. “MLF” should be considered an obsoleted term. OSC2/CLKO OSC1/CLKI PIC16F74 PIC16F77 RE2/AN7/ RE1/AN6/ RE0/AN5/ RA5/AN4/ RA4/T0CKI Product Identification  2003 Microchip Technology Inc. ...

Page 7

... FIGURE 3: PACKAGE MARKING TEMPLATE FOR PIC16F74/77, 44-PIN QFN 44-Lead QFN XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX YYWWNNN  2003 Microchip Technology Inc. PIC16F73/74/76/77 Example PIC16F77 -I/ML 0310017 DS80099G-page 7 ...

Page 8

... Analog input 3. I A/D reference voltage (High) input I/O Digital I/O – Open drain when configured as output. I Timer0 external clock input TTL I/O Digital I/O. I SPI slave select input. I Analog input 4. I/O = input/output ST = Schmitt Trigger input Description P = power  2003 Microchip Technology Inc. ...

Page 9

... This buffer is a Schmitt Trigger input when configured as general purpose I/O and a TTL input when used in the Parallel Slave Port mode (for interfacing to a microprocessor bus). 4: This buffer is a Schmitt Trigger input when configured in RC Oscillator mode and a CMOS input otherwise.  2003 Microchip Technology Inc. PIC16F73/74/76/77 QFP I/O/P ...

Page 10

... Ground reference for logic and I/O pins. 31 7,28 P — Positive supply for logic and I/O pins. 13 12,13, — — These pins are not internally connected. These pins 33,34 should be left unconnected. I/O = input/output ST = Schmitt Trigger input Description P = power  2003 Microchip Technology Inc. ...

Page 11

... Exposed Pad Length Lead Width Lead Length *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC equivalent: M0-220 Drawing No. C04-103  2003 Microchip Technology Inc. PIC16F73/74/76/77 EXPOSED METAL PAD ...

Page 12

... HS Mode) with new date code information. Moved previous silicon issue 5 (Core) to Clarifications/Corrections to the Data Sheet (DS30325B) and added issue 2 (Pinout Correction). Rev G Document (8/03) Added Data Sheet Clarification issues 3 (Pinout Correction) and 4 (Packaging). DS80099G-page 12  2003 Microchip Technology Inc. ...

Page 13

... Serialized Quick Turn Programming (SQTP service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2003, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system ...

Page 14

... Via Quasimodo, 12 20025 Legnano (MI) Milan, Italy Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands Biesbosch 14 NL-5152 SC Drunen, Netherlands Tel: 31-416-690399 Fax: 31-416-690340 United Kingdom 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44-118-921-5869 Fax: 44-118-921-5820 07/28/03  2003 Microchip Technology Inc. ...

Related keywords