LT1260CS#PBF Linear Technology, LT1260CS#PBF Datasheet - Page 9

• Manufacturer Part Number: LT1260CS#PBF
• Description: IC AMP W/SHUTDOWN TRIPLE 16-SOIC
• Manufacturer: Linear Technology

Specifications of LT1260CS#PBF

• Amplifier Type: Current Feedback
• Number Of Circuits: 3
• Slew Rate: 1600 V/µs
• -3db Bandwidth: 130MHz
• Current - Input Bias: 20µA
• Voltage - Input Offset: 2000µV
• Current - Supply: 5mA
• Current - Output / Channel: 60mA
• Voltage - Supply, Single/dual (±): 4 V ~ 30 V, ±2 V ~ 15 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (3.9mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Gain Bandwidth Product: -

APPLICATIO S I FOR ATIO
Differential Input Signal Swing
The differential input swing is limited to about 6V by an
ESD protection device connected between the inputs. In
normal operation, the differential voltage between the
TYPICAL APPLICATIO S
2-Input Video MUX Cable Driver
The application on the first page shows a low cost, 2-
input video MUX cable driver. The scope photo displays
the cable output of a 30MHz square wave driving 150 .
In this circuit the active amplifier is loaded by R
of the disabled amplifier, but in this case it only causes a
1.2% gain error. The gain error can be eliminated by
V
V
V
V
S
IN
S
IN A
= 5V
= 5V
= 0.1V
= V
2-Input Video MUX Switching Response
IN 2
Amplifier Disable Time, A
= 2VPP at 2MHz
R
R
F
G
= 1k
= 110
U
R
L
U
= 150
R
R
F
L
= R
= 100
G
= 1.6k
U
W
V
= 10
LT1259/LT1260 • AI05
LT1259/LT1260 • TA03
U
F
EN
OUTPUT
and R
EN A
EN B
G
input pins is small, so this clamp has no effect. In the
disabled mode however, the differential swing can be the
same as the input swing, and the clamp voltage will set the
maximum allowable input voltage.
configuring each amplifier as a unity-gain follower. The
switching time between channels is 100ns when both
EN A and EN B are driven.
2-Input RGB MUX Cable Driver Demonstration Board
A complete 2-input RGB MUX has been fabricated on PC
Demo Board #039A. The board incorporates two LT1260s
with outputs summed through 75
resistors as shown in the schematic. There are several
things to note about Demo Board #039A:
1. The feedback resistors of the disabled LT1260 load
2. The feedback node has minimum trace length connect-
3. Ground plane is pulled away from R
the enabled amplifier and cause a small (1% to 2%)
gain error depending on the values of R
Configure the amplifiers as unity-gain followers to
eliminate this error.
ing R
sides of the board to minimize stray capacitance.
V
V
F
S
IN
and R
= 5V
= 2VPP at 2MHz
Amplifier Enable/Disable Time, A
G
to minimize stray capacitance.
R
R
F
L
= R
= 100
G
= 1.6k
LT1259/LT1260
back termination
F
LT1259/LT1260 • AI06
and R
V
= 2
F
G
and R
on both
EN
OUTPUT
9
G
.