OP284FSZ Analog Devices Inc, OP284FSZ Datasheet - Page 18

• Manufacturer Part Number: OP284FSZ
• Description: IC OPAMP GP R-R 4.25MHZ LN 8SOIC
• Manufacturer: Analog Devices Inc

Specifications of OP284FSZ

• Slew Rate: 4 V/µs
• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Output Type: Rail-to-Rail
• Gain Bandwidth Product: 4.25MHz
• Current - Input Bias: 80nA
• Voltage - Input Offset: 175µV
• Current - Supply: 2.25mA
• Current - Output / Channel: 10mA
• Voltage - Supply, Single/dual (±): 3 V ~ 36 V, ±1.5 V ~ 18 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Op Amp Type: Precision
• No. Of Amplifiers: 2
• Bandwidth: 4.25MHz
• Supply Voltage Range: ± 1.5V To ± 18V
• Amplifier Case Style: SOIC
• No. Of Pins: 8
• Common Mode Rejection Ratio: 90
• Current, Input Bias: 80 nA
• Current, Input Offset: 50 nA
• Current, Output: ±10 mA
• Current, Supply: 2.25 mA
• Impedance, Thermal: 43 °C/W
• Number Of Amplifiers: Dual
• Package Type: SOIC-8
• Temperature, Operating, Range: -40 to +125 °C
• Voltage, Gain: 1000 V/mV
• Voltage, Input: -15 to +15 V
• Voltage, Noise: 3.9 nV/sqrt Hz
• Voltage, Offset: 250 μV
• Voltage, Output, High: 14.8 V
• Voltage, Output, Low: -14.875 V
• Voltage, Supply: ±15 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

OP184/OP284/OP484
HIGH-SIDE CURRENT MONITOR
In the design of power supply control circuits, a great deal of design
effort is focused on ensuring the long-term reliability of a pass
transistor over a wide range of load current conditions. As a result,
monitoring and limiting device power dissipation is of prime
importance in these designs. The circuit shown in Figure 55 is
an example of a 3 V, single-supply, high-side current monitor that
can be incorporated into the design of a voltage regulator with
fold-back current limiting or a high current power supply with
crowbar protection. This design uses an OP284 rail-to-rail input
voltage range to sense the voltage drop across a 0.1 Ω current shunt.
A P-channel MOSFET, used as the feedback element in the circuit,
converts the differential input voltage of the op amp into a current.
This current is applied to R2 to generate a voltage that is a linear
representation of the load current. The transfer equation for the
current monitor is given by
For the element values shown, the transfer characteristic of the
monitor output is 2.5 V/A.
CAPACITIVE LOAD DRIVE CAPABILITY
The OP284 exhibits excellent capacitive load driving capabilities.
It can drive up to 1 nF, as shown in Figure 30. Even though the
device is stable, a capacitive load does not come without penalty in
bandwidth. The bandwidth is reduced to less than 1 MHz for loads
greater than 2 nF. A snubber network on the output does not
increase the bandwidth, but it does significantly reduce the amount
of overshoot for a given capacitive load.
A snubber consists of a series R-C network (R
Figure 56, connected from the output of the device to ground.
This network operates in parallel with the load capacitor, C
provide the necessary phase lag compensation. The value of the
resistor and capacitor is best determined empirically.
Monitor Output =
MONITOR
OUTPUT
Figure 55. High-Side Load Current Monitor
3V
SI9433
100Ω
M1
R1
S
R2
D
R
R2
2.49kΩ
×
SENSE
0.1Ω
⎛
⎜
⎝
G
R
SENSE
R1
3
2
1/2
OP284
⎞
⎟
⎠
×
3V
I
4
8
L
0.1µF
I
L
S
1
, C
S
), as shown in
3V
L
, to
Rev. I | Page 18 of 24
The first step is to determine the value of Resistor R
starting value is 100 Ω (typically, the optimum value is less than
100 Ω). This value is reduced until the small-signal transient
response is optimized. Next, C
starting point. This value is reduced to the smallest value for
acceptable performance (typically, 1 μF). For the case of a 10 nF
load capacitor on the OP284, the optimal snubber network is
a 20 Ω in series with 1 μF. The benefit is immediately apparent,
as shown in the scope photo in Figure 57. The top trace was taken
with a 1 nF load, and the bottom trace was taken with the 50 Ω,
100 nF snubber network in place. The amount of overshoot and
ringing is dramatically reduced. Table 7 shows a few sample
snubber networks for large load capacitors.
Table 7. Snubber Networks for Large Capacitive Loads
Load Capacitance (C
1 nF
10 nF
100 nF
SNUBBER
1nF LOAD
CIRCUIT
Figure 57. Overshoot and Ringing Are Reduced by Adding a Snubber
ONLY
Figure 56. Snubber Network Compensates for Capacitive Load
IN
100mV p-p
100
90
10
0%
V
IN
Network in Parallel with the 1 nF Load
50mV
L
)
1/2
OP284
50mV
5V
0.1µF
S
B
is determined; 10 μF is a good
W
Snubber Network (R
50 Ω, 100 nF
20 Ω, 1 μF
5 Ω, 10 μF
DLY
R
50Ω
C
100nF
S
S
C
1nF
L
2µs
V
S
5.49µs
OUT
. A good
S
, C
S
)