MCP6285T-E/MS Microchip Technology, MCP6285T-E/MS Datasheet - Page 2

• Manufacturer Part Number: MCP6285T-E/MS
• Description: IC OPAMP 2.2V DUAL W/CS 8MSOP
• Manufacturer: Microchip Technology

Specifications of MCP6285T-E/MS

• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Output Type: Rail-to-Rail
• Slew Rate: 2.5 V/µs
• Gain Bandwidth Product: 5MHz
• Current - Input Bias: 1pA
• Voltage - Input Offset: 3000µV
• Current - Supply: 450µA
• Current - Output / Channel: 25mA
• Voltage - Supply, Single/dual (±): 2.2 V ~ 6 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -

MCP6281/1R/2/3/4/5
1.0
Absolute Maximum Ratings †
V
Current at Input Pins ....................................................±2 mA
Analog Inputs (V
All Other Inputs and Outputs ......... V
Difference Input Voltage ...................................... |V
Output Short Circuit Current .................................Continuous
Current at Output and Supply Pins ............................±30 mA
Storage Temperature....................................–65°C to +150°C
Maximum Junction Temperature (T
ESD Protection On All Pins (HBM; MM) .............. ≥ 4 kV; 400V
DC ELECTRICAL SPECIFICATIONS
DS21811E-page 2
Electrical Characteristics: Unless otherwise indicated, T
V
Input Offset
Input Offset Voltage
Input Offset Voltage
(Extended Temperature)
Input Offset Temperature Drift
Power Supply Rejection Ratio
Input Bias, Input Offset Current and Impedance
Input Bias Current
Input Offset Current
Common Mode Input Impedance
Differential Input Impedance
Common Mode (Note 4)
Common Mode Input Range
Common Mode Rejection Ratio
Common Mode Rejection Ratio
Open-Loop Gain
DC Open-Loop Gain (Large Signal)
Output
Maximum Output Voltage Swing
Output Short Circuit Current
Power Supply
Supply Voltage
Quiescent Current per Amplifier
Note 1:
DD
CM
– V
= V
At Temperature
At Temperature
2:
3:
4:
5:
SS
DD
ELECTRICAL
CHARACTERISTICS
........................................................................7.0V
/2, V
The MCP6285’s V
The current at the MCP6285’s V
This specification does not apply to the MCP6285’s V
The MCP6285’s V
The MCP6285’s V
All parts with date codes November 2007 and later have been screened to ensure operation at V
the other minimum and maximum specifications are measured at 2.4V and/or 5.5V.
Parameters
L
IN
= V
+, V
DD
IN
/2, R
–) †† ........ V
L
= 10 kΩ to V
CM
INB
OUTA
– pin (op amp B) has a common mode range (V
for op amp B (pins V
J
) ......................... .+150°C
/V
SS
SS
INB
– 1.0V to V
– 0.3V to V
+ pin (op amp B) has a voltage range specified by V
L
and CS is tied low. (refer to
ΔV
V
INB
CMRR
CMRR
PSRR
OL
Z
V
Sym
V
V
OS
Z
V
A
I
I
DIFF
CMR
– pin is specified by I
I
I
I
I
OS
SC
CM
, V
OS
OS
DD
OL
Q
B
B
B
/ΔT
DD
DD
DD
OH
A
+ 1.0V
+ 0.3V
– V
OUTA
V
V
SS
A
SS
SS
Min
-3.0
-5.0
300
2.2
= +25 C, V
70
70
65
90
/V
|
—
—
—
—
—
—
—
—
− 0.3
+ 15
INB
+ and V
OUTA
10
10
B
±1.7
±1.0
±1.0
Typ
±25
450
110
90
50
85
80
—
—
—
—
—
DD
13
13
only.
† Notice: Stresses above those listed under “Absolute
Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of
the device at those or any other conditions above those
indicated in the operational listings of this specification is not
implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
†† See Section 4.1.2 “Input Voltage and Current Limits”.
/V
2
Figure 1-2
||6
||3
INB
INB
= +2.2V to +5.5V, V
–) is V
+ pin.
V
V
DD
DD
Max
+3.0
+5.0
200
570
6.0
—
—
—
—
—
—
—
—
—
—
5
+ 0.3
– 15
SS
CMR
and
+ 100 mV.
) of V
Figure
µV/°C T
Units
Ω||pF Note 3
Ω||pF Note 3
mV
mV
mV
mA
dB
pA
pA
nA
pA
dB
dB
dB
µA
V
V
SS
SS
OH
1-3).
+ 100 mV to V
= GND, V
V
T
V
V
V
Note 2
T
T
Note 3
V
V
V
V
0.5V input overdrive
(Note 5)
I
and V
O
© 2008 Microchip Technology Inc.
A
A
A
A
CM
CM
CM
CM
CM
CM
OUT
CM
= -40°C to +125°C,
= -40°C to +125°C,
= +85°C (Note 2)
= +125°C (Note 2)
= 0
= -0.3V to 2.5V, V
= -0.3V to 5.3V, V
= V
= V
= V
= V
= V
= 0.2V to V
OL
SS
SS
SS
SS
SS
.
OUT
Conditions
(Note 1)
(Note 1)
(Note 1)
(Note 1)
(Note 1)
DD
DD
≈ V
= 6.0V. However,
– 100 mV.
DD
DD
/2,
– 0.2V,
DD
DD
= 5V
= 5V