LT6011IDD#TRPBF Linear Technology, LT6011IDD#TRPBF Datasheet - Page 11

• Manufacturer Part Number: LT6011IDD#TRPBF
• Description: IC OP AMP PREC DUAL R-R 8-DFN
• Manufacturer: Linear Technology

Specifications of LT6011IDD#TRPBF

• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Output Type: Rail-to-Rail
• Slew Rate: 0.11 V/µs
• Gain Bandwidth Product: 350kHz
• Current - Input Bias: 150pA
• Voltage - Input Offset: 40µV
• Current - Supply: 260µA
• Current - Output / Channel: 20mA
• Voltage - Supply, Single/dual (±): 2.7 V ~ 36 V, ±1.35 V ~ 18 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-DFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -

APPLICATIO S I FOR ATIO
SI PLIFIED SCHE ATIC
where e
impedance at the input, including the source impedance.
Capacitive Loads
The LT6011/LT6012 can drive capacitive loads up to 500pF
in unity gain. The capacitive load driving capability increases
as the amplifier is used in higher gain configurations. A small
series resistance between the output and the load further
increases the amount of capacitance that the amplifier can
drive.
W
n
–IN
+IN
V
V
+
–
= 14nV/√Hz , i
Figure 1. Some Op Amp Configurations Do Not Require Rail-to-Rail Inputs to Achieve Rail-to-Rail Outputs
500Ω
500Ω
R2
R1
V
REF
V
IN
U
Q7
Q3
R
INVERTING: A
OP AMP INPUTS DO NOT MOVE,
BUT ARE FIXED AT DC BIAS
POINT V
INPUT DOES NOT HAVE TO BE
RAIL-TO-RAIL
Q1
G
R3
n
D1
U
= 0.1pA/√Hz and R
REF
W
–
+
V
= –R
R
D2
F
F
W
/R
Q2
Q8
G
Q4
R4
(One Amplifier)
Q17
C
B
A
S
Q21
U
is the total
V
Q11
IN
B
A
NONINVERTING: A
INPUTS MOVE BY AS MUCH AS
V
MORE
INPUT MAY NOT HAVE TO BE
RAIL-TO-RAIL
IN
Q16
V
, BUT THE OUTPUT MOVES
REF
R
G
–
+
Q15
Q22
Rail-to-Rail Operation
The LT6011/LT6012 outputs can swing to within millivolts
of either supply rail, but the inputs can not. However, for
most op amp configurations, the inputs need to swing less
than the outputs. Figure 1 shows the basic op amp configu-
rations, lists what happens to the op amp inputs and speci-
fies whether or not the op amp must have rail-to-rail inputs.
Select a rail-to-rail input op amp only when really neces-
sary, because the input precision specifications are usually
inferior.
V
R
Q9
F
= 1 + R
Q5
F
/R
G
R5
C2
V
Q10
Q6
IN
Q12
NONINVERTING: A
INPUTS MOVE BY AS MUCH AS
OUTPUT
INPUT MUST BE RAIL-TO-RAIL
FOR OVERALL CIRCUIT
RAIL-TO-RAIL PERFORMANCE
R
C1
+
–
C1
D3
D4
D5
LT6011/LT6012
V
= 1
Q13
Q14
Q18
6011 F01
R6
C3
Q19
Q20
6011 SS
11
OUT
60112fb