LT6600IS8-20 Linear Technology, LT6600IS8-20 Datasheet
LT6600IS8-20
Specifications of LT6600IS8-20
Available stocks
Related parts for LT6600IS8-20
LT6600IS8-20 Summary of contents
Page 1
... Networking or Cellular Base Station Applications n High Speed Test and Measurement Equipment n Medical Imaging n Drop-in Replacement for Differential Amplifi ers L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION LT6600-20 5V 0.1μF R ...
Page 2
... LEAD BASED FINISH TAPE AND REEL LT6600CS8-20 LT6600CS8-20#TR LT6600IS8-20 LT6600IS8-20#TR Consult LTC Marketing for parts specifi ed with wider operating temperature ranges. For more information on lead free part marking, go to: For more information on tape and reel specifi cations, go to: ELECTRICAL CHARACTERISTICS range, otherwise specifi ...
Page 3
ELECTRICAL CHARACTERISTICS range, otherwise specifi cations are 25°C. Unless otherwise specifi PARAMETER Filter Gain 100 IN Filter Gain Temperature Coeffi cient (Note 2) Noise Distortion (Note 4) Differential Output Swing Input Bias ...
Page 4
LT6600-20 TYPICAL PERFORMANCE CHARACTERISTICS Amplitude Response 10 0 –10 –20 –30 –40 –50 –60 – GAIN = 1 – 25°C A –90 0.1 1 FREQUENCY (MHz) Passband Gain and Group Delay ...
Page 5
TYPICAL PERFORMANCE CHARACTERISTICS Distortion vs Signal Level –40 3RD HARMONIC 10MHz INPUT R = 800Ω –50 EACH OUTPUT GAIN = 25°C 2ND A –60 HARMONIC 10MHz INPUT ...
Page 6
LT6600-20 PIN FUNCTIONS – and IN (Pins 1, 8): Input Pins. Signals can be ap- plied to either or both input pins through identical external resistors The DC gain from differential inputs to the IN differential ...
Page 7
APPLICATIONS INFORMATION Interfacing to the LT6600-20 The LT6600-20 requires two equal external resistors set the differential gain to 402Ω/R + fi lter are the voltages V and external components, Figure 1. The difference between + ...
Page 8
LT6600-20 APPLICATIONS INFORMATION In Figure 3 the LT6600-20 is providing 12dB of gain. The gain resistor has an optional 62pF in parallel to improve the passband fl atness near 20MHz. The common mode output voltage is set to 2V. Use ...
Page 9
APPLICATIONS INFORMATION 20 1dB PASSBAND GAIN COMPRESSION POINTS 0 1MHz 85°C –20 3RD HARMONIC 85°C –40 3RD HARMONIC 25°C –60 2ND HARMONIC –80 25°C 2ND HARMONIC –100 85°C –120 1MHz INPUT LEVEL (V Figure 6. ...
Page 10
LT6600-20 APPLICATIONS INFORMATION Noise The noise performance of the LT6600-20 can be evaluated with the circuit of Figure 7. Given the low noise output of the LT6600-20 and the 6dB attenuation of the transformer coupling network necessary to ...
Page 11
... MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa- tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 12
... Lowpass and Bandpass Filter Designs Up to 10MHz, Differential Outputs 86dB S/N with 3V Supply, SO-8 82dB S/N with 3V Supply, SO-8 www.linear.com ● OUT OUT – – OUT OUT Transient Response, Gain = 1 66002 TA03 100ns/DIV LT 0409 REV B • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2003 66002fb ...