AD8005AR Analog Devices Inc, AD8005AR Datasheet
AD8005AR
Specifications of AD8005AR
Available stocks
Related parts for AD8005AR
AD8005AR Summary of contents
Page 1
FEATURES Ultralow Power 400 A Power Supply Current ( Specified for Single Supply Operation High Speed 270 MHz, –3 dB Bandwidth (G = +1) 170 MHz, –3 dB Bandwidth (G = +2) 280 V/ s Slew Rate ...
Page 2
AD8005–SPECIFICATIONS 5 V SUPPLIES (@ Parameter DYNAMIC PERFORMANCE –3 dB Small Signal Bandwidth Bandwidth for 0.1 dB Flatness Large Signal Bandwidth Slew Rate (Rising Edge) Settling Time to 0.1% DISTORTION/NOISE PERFORMANCE Total Harmonic Distortion ...
Page 3
V SUPPLY (@ Parameter DYNAMIC PERFORMANCE –3 dB Small Signal Bandwidth Bandwidth for 0.1 dB Flatness Large Signal Bandwidth Slew Rate (Rising Edge) Settling Time to 0.1% DISTORTION/NOISE ...
Page 4
... AD8005AN AD8005AR AD8005AR-REEL AD8005ART-REEL AD8005AR-REEL7 AD8005ART-REEL7 CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD8005 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality ...
Page 5
200mV p-p OUT – +10 – 499 F –3 –4 – FREQUENCY – MHz Figure 4. Frequency Response; ...
Page 6
AD8005–Typical Characteristics – p-p –50 OUT 3RD –60 –70 2ND –80 –90 –100 1 FREQUENCY – MHz Figure 10. Distortion vs. Frequency; V MIN = –0.06 MAX = 0.03 p-p/MAX ...
Page 7
– – –20 –25 –30 –35 –40 –45 –50 –55 0.03 0.1 1 FREQUENCY – MHz Figure 16. CMRR vs. Frequency +5V AND ...
Page 8
AD8005–Typical Characteristics PROBE 0.01 F 0.01 F PROBE : TEK P6137 C = 10pF NOMINAL LOAD Figure 22. Test Circuit + Package 2.49 ...
Page 9
APPLICATIONS Driving Capacitive Loads Capacitive loads interact with an op amp’s output impedance to create an extra delay in the feedback path. This reduces circuit stability, and can cause unwanted ringing and oscilla- tion. A given value of capacitance causes ...
Page 10
AD8005 Single-Ended-to-Differential Conversion Many single supply ADCs have differential inputs. In such cases, the ideal common-mode operating point is usually halfway between supply and ground. Figure 31 shows how to convert a single-ended bipolar signal into a differential signal with ...
Page 11
Increasing Feedback Resistors Unlike conventional voltage feedback op amps, the choice of feed- back resistor has a direct impact on the closed-loop bandwidth and stability of a current feedback op amp circuit. Reducing the resistance below the recommended value makes ...
Page 12
AD8005 0.0669 (1.70) 0.0590 (1.50) 0.0512 (1.30) 0.0354 (0.90) OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 8-Lead Plastic DIP (N-8) 0.430 (10.92) 0.348 (8.84 0.280 (7.11) 0.240 (6.10 0.325 (8.25) 0.300 (7.62) 0.060 (1.52) PIN ...