NE5534ADG ON Semiconductor, NE5534ADG Datasheet - Page 10

• Manufacturer Part Number: NE5534ADG
• Description: IC OPAMP SGL LOW NOISE 8-SOIC
• Manufacturer: ON Semiconductor

Specifications of NE5534ADG

• Amplifier Type: General Purpose
• Number Of Circuits: 1
• Slew Rate: 13 V/µs
• Gain Bandwidth Product: 10MHz
• Current - Input Bias: 500nA
• Voltage - Input Offset: 500µV
• Current - Supply: 4mA
• Current - Output / Channel: 38mA
• Voltage - Supply, Single/dual (±): ±3 V ~ 20 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Number Of Channels: 1
• Common Mode Rejection Ratio (min): 70 dB
• Input Voltage Range (max): Positive Rail - 3 V
• Input Voltage Range (min): Negative Rail + 3 V
• Input Offset Voltage: 4 mV
• Input Bias Current (max): 1.5 uA
• Operating Supply Voltage: +/- 20 V
• Supply Current: 8 mA
• Maximum Power Dissipation: 750 mW
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Dual Supply Voltage: +/- 5 V, +/- 9 V, +/- 12 V
• Maximum Dual Supply Voltage: +/- 20 V
• Minimum Dual Supply Voltage: +/- 3 V
• Mounting Style: SMD/SMT
• Shutdown: No
• Technology: Bipolar
• Voltage Gain Db: 100 dB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: [e-mail]
ON Semiconductor and
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any
liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over
time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under
its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part.
SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
NOTE 2
SEATING
PLANE
−T−
H
8
1
F
−A−
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
G
5
4
0.13 (0.005)
D
N
−B−
8−Pin Plastic Dual In−Line Package (PDIP−8)
C
M
K
T
A
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Japan: ON Semiconductor, Japan Customer Focus Center
M
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
PACKAGE DIMENSIONS
B
http://onsemi.com
M
CASE 626−05
N SUFFIX
ISSUE L
10
L
M
J
NOTES:
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
1. DIMENSION L TO CENTER OF LEAD WHEN
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
3. DIMENSIONING AND TOLERANCING PER ANSI
FORMED PARALLEL.
SQUARE CORNERS).
Y14.5M, 1982.
DIM
A
B
C
D
F
G
H
K
L
M
N
J
MILLIMETERS
MIN
9.40
6.10
3.94
0.38
1.02
0.76
0.20
2.92
0.76
−−−
2.54 BSC
7.62 BSC
10.16
MAX
6.60
4.45
0.51
1.78
1.27
0.30
3.43
1.01
10
_
0.370
0.240
0.155
0.015
0.040
0.030
0.008
0.030
0.115
MIN
−−−
0.100 BSC
0.300 BSC
INCHES
NE5534/D
0.400
0.260
0.175
0.020
0.070
0.050
0.012
0.135
0.040
MAX
10
_