CAT811TTBI-T3 ON Semiconductor, CAT811TTBI-T3 Datasheet
CAT811TTBI-T3
Specifications of CAT811TTBI-T3
CAT811TTBI-T3TR
Available stocks
Related parts for CAT811TTBI-T3
CAT811TTBI-T3 Summary of contents
Page 1
Microprocessor Power Supply Supervisors with Manual Reset FEATURES Precision monitoring of +5.0 V (± 5%, ± 10%, ± 20%), +3.3 V (± 5%, ± 10%), +3.0 V (± 10%) and +2.5 V (± 5%) power supplies Manual ...
Page 2
CAT811, CAT812 PIN DESCRIPTION Pin Number Name CAT811 CAT812 1 1 GND ¯¯¯¯¯¯ 2 — RESET — 2 RESET ¯¯¯ BLOCK DIAGRAM MR V TOLERANCE TOLERANCE CC Doc. No. MD-3005 ...
Page 3
ABSOLUTE MAXIMUM RATINGS Parameters Any pin with respect to ground Input Current ¯¯¯¯¯¯ Output Current RESET, RESET Rate of Raise Continuous Power Dissipations Derate 4mW/ºC above +70ºC (SOT-143) Storage Temperature Operating Ambient Temperature Lead Soldering (10 ...
Page 4
CAT811, CAT812 ELECTRICAL OPERATING CHARACTERISTICS (continued Full range -40°C to +85°C unless otherwise noted. Typical values L/M/J versions 3.3V for the T/S versions Parameter Symbol Reset Threshold Tempco ...
Page 5
TYPICAL OPERATING CHARACTERISTICS V = Full range -40°C to +85°C unless otherwise noted. Typical values L/M/J versions 3.3V for the T/S versions POWER-UP RESET TIMEOUT VS. TEMPERATURE 260 240 V ...
Page 6
CAT811, CAT812 DETAILED DESCRIPTION RESET TIMING The reset signal is asserted LOW for the CAT811 and HIGH for the CAT812 when the power supply voltage falls below the threshold trip voltage and remains asserted for at least 140ms after the ...
Page 7
VALID RESET WITH V UNDER 1.0V CC ¯¯¯¯¯¯ pin known To ensure that the CAT811 RESET state when V is under 1.0V, a 100kΩ pull-down CC ¯¯¯¯¯¯ resistor between RESET pin recommended; the value is not critical. ...
Page 8
CAT811, CAT812 OTHER SUPERVISORY PRODUCTS Function CAT1161/3 With 16k Bit Serial EEPROM Memory Watchdog Timer Manual Reset Input Active Low Reset Active High Reset Dual Polarity Reset Outputs 8-pin DIP Package and SOIC Doc. No. MD-3005 Rev. V CAT1162 CAT809 ...
Page 9
PACKAGE OUTLINE DRAWING (1) SOT-143 4-Lead (TB TOP VIEW b1 SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC satndard TO-253. © 2010 SCILLC. All rights reserved. Characteristics subject to ...
Page 10
... The standard lead finish is NiPdAu. Contact factory for other package availability. (3) This device used in the above example is a CAT811STBI-GT10 (SOT-143 4-Lead, Push-Pull/Active Low Output, trip level of 2.85V to 3.00V, NiPdAu, Tape & Reel, 10,000/Reel) (4) For additional package and temperature options, please contact your nearest ON Semiconductor Sales office. Doc. No. MD-3005 Rev. V (1) ...
Page 11
... Add Block Diagrams 18-Apr-08 S Updated Package Outline Drawing Update Example of Ordering Information 5-Nov-08 T Change logo and fine print to ON Semiconductor 19-May-10 U Update Electrical Operating Characteristics 20-July-10 V Update Figure 2 are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to ON Semiconductor and any products herein ...