CAT1026WI-25-T3 ON Semiconductor, CAT1026WI-25-T3 Datasheet
CAT1026WI-25-T3
Specifications of CAT1026WI-25-T3
CAT1026WI-25-T3TR
Related parts for CAT1026WI-25-T3
CAT1026WI-25-T3 Summary of contents
Page 1
Dual Voltage Supervisory Circuits with I²C Serial 2k-bit CMOS EEPROM FEATURES Precision V Power Supply Voltage Monitor CC — 3.3 V and 3 V systems — Five threshold voltage options Additional voltage monitoring — Externally adjustable down to ...
Page 2
CAT1026, CAT1027 BLOCK DIAGRAM EXTERNA L LOAD V CC WORDADDRESS V SS START/STOP SDA LOGIC CONTR OL LOGIC V CC Monitor RESET Controller - V REF AuxiliaryVoltage Monitor RESET (CAT1026) V SENSE + V LOW - V ...
Page 3
PIN DESCRIPTION : RESET OUTPUTs ¯¯¯¯¯¯ RESET/RESET (RESET CAT1026 Only) ¯¯¯¯¯¯ can be used These are open drain pins and RESET as a manual reset trigger input. By forcing a reset condition on the pin the device will initiate and ...
Page 4
CAT1026, CAT1027 ABSOLUTE MAXIMUM RATINGS Parameters Temperature Under Bias Storage Temperature Voltage on any Pin with Respect to Ground V with Respect to Ground CC Package Power Dissipation Capability (T Lead Soldering Temperature (10 s) (3) Output Short Circuit Current ...
Page 5
CAPACITANCE T = 25º 1.0 MHz Symbol Test (1) C Output Capacitance OUT (1) C Input Capacitance IN AC CHARACTERISTICS 5.5 V and over the recommended temperature ...
Page 6
CAT1026, CAT1027 VOLTAGE MONITOR AND RESET CIRCUIT AC CHARACTERISTICS Symbol Parameter t Reset Timeout PURST RESET Output Delay RDP Glitch Reject Pulse Width GLITCH CC t Watchdod Timeout Delay ...
Page 7
DEVICE OPERATION Reset Controller Description The CAT1026 and CAT1027 precision RESET controllers ensure correct system operation during brownout and power up/down conditions. They are configured with open drain RESET outputs. During power-up, the RESET outputs remain active until V reaches ...
Page 8
CAT1026, CAT1027 Figure 1. RESET Output Timing RVALID t V PURST CC RESE T RESE T Figure 2: Auxiliary Voltage Monitor Timing V REF V SENSE V LOW Figure 3: Auxiliary Voltage Monitor Externally adjustable threshold V ...
Page 9
EMBEDDED EEPROM OPERATION The CAT1026 and CAT1027 feature a 2-kbit embedded serial EEPROM that supports the I transmission protocol. This Inter-Integrated Circuit Bus protocol defines any device that sends data to the bus transmitter and any device ...
Page 10
CAT1026, CAT1027 ACKNOWLEDGE After a successful data transfer, each receiving device is required to generate an acknowledge. The acknowledging device pulls down the SDA line during the ninth clock cycle, signaling that it received the 8 bits of data. The ...
Page 11
Page Write The CAT1026 and CAT1027 write bytes of data in a single write cycle, using the Page Write operation. The page write operation is initiated in the same manner as the byte write operation, however instead ...
Page 12
CAT1026, CAT1027 Acknowledge Polling Disabling of the inputs can be used to take advantage of the typical write cycle time. Once the stop condition is issued to indicate the end of the host’s write opration, the CAT1026 and CAT1027 initiates ...
Page 13
Immediate/Current Address Read The CAT1026 and CAT1027 address counter contains the address of the last byte accessed, incremented by one. In other words, if the last READ or WRITE access was to address N, the READ immediately following would access ...
Page 14
CAT1026, CAT1027 PACKAGE OUTLINE DRAWINGS (1)(2) PDIP 8-Lead 300 mils (L) PIN # 1 IDENTIFICATION D TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MS-001. Doc. No. MD-3010 Rev. P ...
Page 15
SOIC 8-Lead 150 mils (W) PIN # 1 IDENTIFICATION TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. © 2009 SCILLC. All rights reserved. Characteristics subject ...
Page 16
CAT1026, CAT1027 (1)(2) TSSOP 8-Lead ( TOP VIEW D SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153 Doc. No. MD-3010 Rev. P SYMBOL ...
Page 17
MSOP 8-Lead ( TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-187. © 2009 SCILLC. All rights reserved. Characteristics subject to change ...
Page 18
CAT1026, CAT1027 (1)(2) TDFN 8-Pad (ZD4) D PIN#1 INDEX AREA TOP VIEW SYMBOL MIN NOM A 0.70 0.75 A1 0.00 0.02 A3 0.20 REF b 0.23 0.30 D 2.90 3.00 D2 2.20 — E 2.90 3.00 ...
Page 19
... All packages are RoHS-compliant (Lead-free, Halogen-free). (2) The standard lead finish is NiPdAu. (3) The device used in the above example is a CAT1026WI-30-GT3 (SOIC, Industrial Temperature, 3.0 - 3.15 V, NiPdAu, Tape & Reel, 3,000/Reel). (4) For additional package and temperature options, please contact your nearest ON Semiconductor Sales office. ...
Page 20
... Update Example of Ordering Information Update Package Outline Drawings 11/28/2007 M Update Example of Ordering Information Add “MD-“ to document number 7-Nov-08 N Change logo and fine print to ON Semiconductor 05-Mar-09 O Update Ordering Information (Remove 2,000/Reel) 14-Jul-09 P Update Ordering Information table ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein ...