MIC2772-L3L3YML TR Micrel Inc, MIC2772-L3L3YML TR Datasheet
MIC2772-L3L3YML TR
Specifications of MIC2772-L3L3YML TR
MIC2772-L3L3YML TR
MIC2772-L3L3YMLTR
MIC2772-L3L3YMLTR
Related parts for MIC2772-L3L3YML TR
MIC2772-L3L3YML TR Summary of contents
Page 1
... General Description The MIC2772 is a dual power supply supervisor that provides under-voltage monitoring and power-on reset generation. It may replace two discrete voltage supervisors such as MIC1810, MIC1815, MIC809, MIC811, MIC6315, etc. The two voltage supervisors are completely independent. Each functional block features an under-voltage detector, a delay-generator, and a de-bounced manual reset input ...
Page 2
... Micrel Ordering Information Part Number Standard MIC2772-L2L3YML MIC2772-M2M3YML (1) MIC2772-L3L3BML MIC2772-L3L3YML (1) MIC2772-M3M3BML MIC2772-M3M3YML (1) MIC2772-T3T3BML MIC2772-T3T3YML (1) MIC2772-S3S3BML MIC2772-S3S3YML MIC2772-T2T3YML MIC2772-S2S3YML MIC2772-L3T3YML MIC2772-M3S3YML : Note 1. Available now. 2. Contact factory. Pin Configuration April 2005 Top Mark Pb-Free Standard Pb-Free (2) (2) (1) UP2 (1) UP3 (1) UP4 (1) UP5 (2) (2) (2) (2) ...
Page 3
... Digital Output; open-drain; supervisor 1. Asserted low whenever VCC1 falls below the threshold voltage. It remains asserted for no less than t de-asserted after VCC1 returns above the threshold. Analog Input. Power supply input for supervisor 1. 3 MIC2772 later. /MR1 may RESET1 later. /MR2 RESET2 ...
Page 4
... CCn SINK ≥ 2.5V 1.2mA CCn SINK ≥ 1V µ CCn SINK /RESET not asserted V > 4.0V THn V < 4.0V THn V > 4.0V THn V < 4.0V THn 4 MIC2772 (2) ° ° ).... - + )................ 93°C/W JA ≤ T ≤ MIN A MAX Min Typ Max Units 30 10 µ µA ...
Page 5
... Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF. Timing Diagram V CCn /MR n /RESET n April 2005 Condition → /RESETn < V /MRn < Reset Occurs No Reset Occurs RST MIC2772 Timing Diagram 5 MIC2772 Min Typ Max Units 0.5 10 100 RST M9999-042605 (408) 955-1690 µs µ ...
Page 6
... MOSFET structure. A pull-up resistor must be used to pull this output to some voltage. For most applications, this voltage will be the same power supply that supplies VCC to MIC2772 possible however to tie this resistor to some other voltage. This will allow the MIC2772 to monitor one voltage while level-shifting the /RESET output to some other voltage ...
Page 7
... The data was taken by adding negative-going square-wave pulse input voltage set at 0.5V above actual measured threshold for the part being characterized. Figure 1 shows the graph for the MIC2772[UP3] and Figure 2 shows the graph for the MIC2772[UP5] Typical Transient Response ...
Page 8
... Micrel April 2005 8 MIC2772 M9999-042605 (408) 955-1690 ...
Page 9
... A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. April 2005 8-Pin 2mm X 2mm MLF (ML) © 2005 Micrel, Incorporated. 9 MIC2772 M9999-042605 (408) 955-1690 ...