AP1184K5-25L-13 Diodes Inc, AP1184K5-25L-13 Datasheet - Page 6

• Manufacturer Part Number: AP1184K5-25L-13
• Description: IC REG LDO 4.0A 2.5V TO263-5L
• Manufacturer: Diodes Inc

Specifications of AP1184K5-25L-13

• Regulator Topology: Positive Fixed
• Voltage - Output: 2.5V
• Voltage - Input: Up to 16V
• Voltage - Dropout (typical): 0.7V @ 4A
• Number Of Regulators: 1
• Current - Output: 4A
• Current - Limit (min): 4.2A
• Operating Temperature: 0°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: TO-263-5, D²Pak (5 leads + Tab), TO-263BA
• Number Of Outputs: 1
• Polarity: Positive
• Input Voltage Max: 16 V
• Output Voltage: 2.5 V
• Output Type: Fixed
• Dropout Voltage (max): 0.38 V at 1500 mA
• Output Current: 4 A
• Line Regulation: 0.2 %
• Load Regulation: 25 mV
• Maximum Power Dissipation: 4.4 W
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: AP1184K525L-13; AP1184K525LDITR

Functional Descriptions
The AP1184-ADJ keeps a constant 1.25V between the Vsense pin and the Adj pin. By placing a resistor R1 across these two pins and
connecting the Vsense and Vout pin together, a constant current flows through R1, adding to the Iadj current and into the R2 resistor
producing a voltage equal to the (1.25/R1)*R2 + Iadj*R2. This voltage is then added to the 1.25V to set the output voltage. This is
summarized in the above equation. Since the minimum load current requirement of the AP1184-ADJ is 10mA, R1 is typically selected to
be a 121Ω resistor so that it automatically satisfies this condition. Notice that since the Iadj is typically in the range of 50uA it only adds a
small error to the output voltage and should be considered when very precise output voltage setting is required.
Load Regulation
Since the AP1184 has separate pins for the output (Vout) and the sense (Vsense), it is ideal for providing true remote sensing of the
output voltage at the load. This means that the voltage drops due to parasitic resistance such as PCB traces between the regulator and
the load are compensated for using remote sensing. Figure following shows a typical application of the AP1184-ADJ with remote sensing.
Stability
The AP1184-XXX requires the use of an output capacitor as part of the frequency compensation in order to make the regulator stable.
Typical designs for the microprocessor applications use standard electrolytic capacitors with typical ESR in the range of 50 to 100mΩ
and an output capacitance of 100uF to 1000uF. Fortunately as the capacitance increases, the ESR decreases resulting in a fixed RC
time constant. The AP1184-XXX takes advantage of the phenomena in making the overall regulator loop stable. For most applications a
minimum of 100uF aluminum electrolytic capacitor insures both stability and good transient response.
Thermal Design
The AP1184-XXX incorporates an internal thermal shutdown that protects the device when the junction temperature exceeds the
allowable maximum junction temperature. Although this device can operate with junction temperatures in the range of 150
recommended that the selected heat sink be chosen such that during maximum continuous load operation, the junction temperature is
kept below this number. The example below shows the steps in selecting the proper surface mount package.
AP1184 Rev. 5
Vctrl
Vctrl
Vin
Vin
Vout = Vref (1+R2/R1) + Iadj * R2 where : Vref = 1.25V & Iadj=50uA Typically
Vin
Vctrl
4A ULTRA LOW DROPOUT POSITIVE ADJUSTABLE OR
AP1184-ADJ
(Continued)
Adj
www.diodes.com
AP1184-ADJ
Adj
Vsense
6 of 12
Vout
Iadj=50uA
Vsense
R1
R2
Vref
FIXED-MODE REGULATOR
R1+
R2+
SEPTEMBER 2008
Vout
R
©
AP1184
L
Diodes Incorporated
o
C, it is