TC1054-2.6VCT713 Microchip Technology, TC1054-2.6VCT713 Datasheet - Page 2

• Manufacturer Part Number: TC1054-2.6VCT713
• Description: IC CMOS LDO 2.6V 50MA SOT23A-5
• Manufacturer: Microchip Technology

Specifications of TC1054-2.6VCT713

• Regulator Topology: Positive Fixed
• Voltage - Output: 2.6V
• Voltage - Input: 2.7 ~ 6 V
• Voltage - Dropout (typical): 0.085V @ 50mA
• Number Of Regulators: 1
• Current - Output: 50mA (Min)
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: SOT-23-5, SC-74A, SOT-25
• Number Of Outputs: 1
• Polarity: Positive
• Input Voltage Max: 6 V
• Output Voltage: 2.6 V
• Output Type: Fixed
• Dropout Voltage (max): 120 / 400 mV
• Output Current: 50 mA
• Line Regulation: 0.05 %
• Load Regulation: 0.5 %
• Voltage Regulation Accuracy: 0.5 %
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Limit (min): -
• Lead Free Status / Rohs Status: Details
• Other names: TC10542.6VCT713

TC1054/TC1055/TC1186
1.0
Absolute Maximum Ratings †
Input Voltage ....................................................................6.5V
Output Voltage .....................................(-0.3V) to (V
Power Dissipation ......................... Internally Limited (Note 6)
Maximum Voltage on Any Pin ...................V
Operating Junction Temperature Range .. -40°C < T
Storage Temperature.....................................-65°C to +150°C
DC CHARACTERISTICS
DS21350D-page 2
Electrical Specifications: Unless otherwise noted, V
Boldface type specifications apply for junction temperatures of -40°C to +125°C.
Input Operating Voltage
Maximum Output Current
Output Voltage
V
Line Regulation
Load Regulation:
Dropout Voltage:
Supply Current
Shutdown Supply Current
Power Supply Rejection Ratio
Output Short Circuit Current
Thermal Regulation
Thermal Shutdown Die
Temperature
Thermal Shutdown Hysteresis
Note 1: V
OUT
Temperature Coefficient
2:
3: Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested
4: Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal
5: Thermal Regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied,
6: The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction
7: Hysteresis voltage is referenced by V
8: The minimum V
9: Apply for junction temperatures of -40C to +85C.
ELECTRICAL
CHARACTERISTICS
TC V
over a load range from 0.1 mA to the maximum specified output current. Changes in output voltage due to heating
effects are covered by the thermal regulation specification.
value.
excluding load or line regulation effects. Specifications are for a current pulse equal to I
temperature and the thermal resistance from junction-to-air (i.e., T
dissipation causes the device to initiate thermal shutdown. Please see Section 5.0 “Thermal Considerations”, “Ther-
mal Considerations”, for more details.
Parameters
R
is the regulator output voltage setting. For example: V
OUT
TC1054; TC1055
TC1055; TC1186
= (V
OUT
MAX
IN
V
TC1186
TC1186
OUT
has to justify the conditions: V
– V
x ΔT
OUT
MIN
ΔV
ΔV
ΔV
)x 10
V
TCV
I
OUT
IN
OUT
OUT
PSRR
I
OUT
V
OUT
ΔT
Sym
I
INSD
T
V
-V
OUT
I
6
IN
IN
SD
IN
SD
OUT
/V
MAX
/ΔV
OUT
/ΔP
SC
+0.3V to -0.3V
OUT
IN
D
R
.
IN
J
< 125°C
V
+ 0.3V)
IN
R
Min
100
150
– 2.5% V
= V
2.7
50
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
IN
OUT
≥ V
+ 1V, I
R
R
+ V
0.05
0.05
0.04
Typ
180
270
300
160
0.5
0.5
R
±0.5% V
20
40
65
85
50
64
10
—
—
—
—
2
= 1.8V, 2.5V, 2.7V, 2.85V, 3.0V, 3.3V, 3.6V, 4.0V, 5.0V.
L
† Stresses above those listed under "Absolute Maximum
Ratings" may cause permanent damage to the device. These
are stress ratings only and functional operation of the device
at these or any other conditions above those indicated in the
operation sections of the specifications is not implied.
Exposure to Absolute Maximum Rating conditions for
extended periods may affect device reliability.
DROPOUT
= 100 µA, C
A
R
, T
Max
0.35
120
250
400
450
+ 2.5%
and V
6.0
0.5
80
—
—
—
—
—
—
—
—
—
—
—
J
2
3
, θ
L
JA
= 3.3 µF, SHDN > V
). Exceeding the maximum allowable power
IN
≥ 2.7V for I
ppm/°C Note 2
Units
V/W
mA
mV
mA
µA
µA
dB
°C
°C
%
%
V
V
© 2007 Microchip Technology Inc.
L
Note 8
TC1054
TC1055
TC1186
Note 1
(V
(Note 3)
I
I
I
I
I
I
I
SHDN = V
SHDN = 0V
f ≤ 1 kHz
V
Notes 5, 6
L
L
L
L
L
L
L
MAX
OUT
L
R
= 0.1 mA to I
= 0.1 mA to I
= 100 µA
= 20 mA
= 50 mA
= 100 mA
= 150 mA (Note 4)
= 0.1 mA to I
+ 1V) ≤ V
at V
= 0V
IH
IN
, T
Conditions
IH
= 6V for T = 10 ms.
A
, I
= +25°C.
IN
L
OUT
OUT
= 0 µA (Note 9)
≤ 6V
OUT
MAX
MAX
MAX
.