B72714D0200A060 EPCOS Inc, B72714D0200A060 Datasheet

Page 1

CeraDiodes Standard series Series/Type: Date: November 2010 © EPCOS AG 2010. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. ...

Page 2

CeraDiodes Standard series Features ESD protection to IEC 61000-4-2, level 4 Bidirectional ESD protection in one component No change in ESD protection performance at temperatures (temperature derating) Use of parasitic capacitance for EMI suppression and high-frequency ...

Page 3

... Standard series Electrical specifications and ordering codes Maximum ratings ( and characteristics (T op,max Type Ordering code Array, 4-fold, 0508, no semiconductor diode equivalent CDA4C20GTA B72714D0200A060 22 Array, 4-fold, 0612, no semiconductor diode equivalent CDA5C20GTA B72724D0200A062 22 Single, 0201, no semiconductor diode equivalent CDS1C05GTA B72440D0050A060 Single, 0402, SOD-723 CDS2C05GTA ...

Page 4

CeraDiodes Standard series Dimensional drawings Single device Array device Please read Cautions and warnings and Important notes at the end of this document. Dimensions in mm Case (inch) 0201 0402 size (mm) 0603 1005 Min. Max. Min. Max. Min. Max. ...

Page 5

CeraDiodes Standard series Recommended solder pads Single device Array device Please read Cautions and warnings and Important notes at the end of this document. Dimensions in mm Case size (inch) 0201 (mm) 0603 A 0.3 B 0.25 C 0.3 Dimensions ...

Page 6

CeraDiodes Standard series Pin configurations Single device Pin P1 P2 Array device Pin Please read Cautions and warnings and Important notes at the end of this document. Description GND I/O line Description ...

Page 7

CeraDiodes Standard series Termination Single device Array device Please read Cautions and warnings and Important notes at the end of this document. Page ...

Page 8

... Important notes at the end of this document. Packing unit Type pcs. 15000 CDS1C05GTA 10000 CDS2C05GTA 10000 CDS2C15GTA 4000 CDA4C20GTA 4000 CDS3C05GTA 4000 CDS3C09GTA 4000 CDS3C15GTA 4000 CDS3C20GTA 3000 CDA5C20GTA 4000 CDS4C12GTA Page Ordering code B72440D0050A060 B72590D0050A060 B72590D0150A060 B72714D0200A060 B72500D0050A060 B72500D0090A060 B72500D0150A060 B72500D0200A060 B72724D0200A062 B72570D0120A060 ...

Page 9

CeraDiodes Standard series 1 Taping and packing for chip and array CeraDiodes 1.1 Cardboard tape (taping to IEC 60286-3) Dimensions in mm Case size (inch) (mm) Compartment width Compartment length Sprocket hole diameter Sprocket hole pitch Distance center hole to ...

Page 10

CeraDiodes Standard series 1.2 Blister tape (taping to IEC 60286-3) Dimensions in mm Case size (inch) (mm) Compartment width Compartment length Compartment height Sprocket hole diameter Compartment hole diameter Sprocket hole pitch Distance center hole to center compartment Pitch of ...

Page 11

CeraDiodes Standard series 1.3 Reel packing Dimensions in mm Reel diameter A Reel width (inside Reel width (outside Package: 8-mm tape Reel material: Plastic 1.4 Packing units Case size 180-mm reel (inch) / (mm) pieces 0201 ...

Page 12

CeraDiodes Standard series Soldering directions 1 Reflow soldering temperature profile Recommended temperature characteristic for reflow soldering following JEDEC J-STD-020D Profile feature Preheat and soak - Temperature min - Temperature max - Time Average ramp-up rate Liquidous temperature Time at liquidous ...

Page 13

CeraDiodes Standard series 2 Soldering guidelines The use of mild, non-activated fluxes for soldering is recommended, as well as proper cleaning of the PCB. The components are suitable for reflow soldering to JEDEC J-STD-020D. 3 Solder joint profiles / solder ...

Page 14

CeraDiodes Standard series 3.3.1 Solder joint profiles for nickel barrier termination Good and poor solder joints caused by amount of solder in infrared reflow soldering Please read Cautions and warnings and Important notes at the end of this document. Page ...

Page 15

CeraDiodes Standard series 4 Solderability tests Test Standard Test conditions / Sn-Pb soldering Wettability IEC Immersion in 60068-2-58 60/40 SnPb solder using non-activated flux at 215 3 C for 3 0.3 s Leaching IEC Immersion in resistance 60068-2-58 60/40 SnPb ...

Page 16

CeraDiodes Standard series 5 Notes for proper soldering 5.1 Preheating and cooling The average ramp-up rate must not exceed 3 C/s. The cooling rate must not exceed 8 C/s. 5.2 Repair / rework Manual soldering with a soldering iron must ...

Page 17

CeraDiodes Standard series 5.7 Placement of components on circuit board advantage to place the components on the board before soldering so that their two termi- nals do not enter the solder oven at different times. Ideally, both ...

Page 18

CeraDiodes Standard series Symbols and terms CeraDiode Semiconductor diode C max C typ leak ...

Page 19

CeraDiodes Standard series Cautions and warnings General Some parts of this publication contain statements about the suitability of our CeraDiodes for cer- tain areas of application, including recommendations about incorporation/design-in of these prod- ucts into customer applications. The statements are ...

Page 20

CeraDiodes Standard series Storage Only store CeraDiodes in their original packaging. Do not open the package before storage. Storage conditions in original packaging: temperature -25 to +45 C, relative humidity 75% an- nual average, maximum 95%, dew precipitation is inadmissible. ...

Page 21

CeraDiodes Standard series Operation Use CeraDiodes only within the specified operating temperature range. Use CeraDiodes only within specified voltage and current ranges. Environmental conditions must not harm a CeraDiode. Only use them in normal atmospheric conditions. Reducing the atmosphere (e.g. ...

Page 22

Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical ...