MCR100JZHJ000

Manufacturer Part NumberMCR100JZHJ000
DescriptionRES 0.0 OHM 1W 2512 SMD
ManufacturerRohm Semiconductor
SeriesMCR100
MCR100JZHJ000 datasheet
 


Specifications of MCR100JZHJ000

Resistance (ohms)0.0Power (watts)1W
CompositionThick FilmToleranceJumper
Size / Dimension0.248" L x 0.126" W (6.30mm x 3.20mm)Height0.022" (0.55mm)
Lead StyleSurface Mount (SMD - SMT)Package / Case2512 (6432 Metric)
Resistance In Ohms0.0Case2512 (6432 metric)
Lead Free Status / RoHS StatusLead free / RoHS CompliantFeatures-
Temperature Coefficient-Other namesRHM0.0BCTR
1
Page 1
2
Page 2
3
Page 3
4
Page 4
Page 1/4

Download datasheet (79Kb)Embed
Next
Resistors
Thick Film Chip Resistors
MCR100 (2512 size : 1W)
Features
1) Made of same material as the general purpose chip resistors (MCR10 / 18).
2) Highly reliable chip resistor
Ruthenium oxide dielectric offers superior resistance to the elements.
3) Electrodes not corroded by soldering
Suitable for re-flow soldering.
4) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with
the product before using or ordering it.
Ratings
Item
Rated power
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
100
80
60
40
20
0
−55
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the limiting element voltage, the voltage rating is
equal to the maximum operating voltage.
E: Rated voltage (V)
E = P × R
P: Rated power (W)
R: Nominal resistance (Ω)
Nominal resistance
See Table 1.
Operating temperature
Jumper type
Resistance
Max. 50mΩ
Rated current
4A
−55°C to+125°C
Operating temperature
•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
Conditions
0
70
100
125
AMBIENT TEMPERATURE (°C)
Fig.1
Table 1
Resistance range
Resistance tolerance
F (±1%)
10≤R≤82k
J (±5%)
1.0≤R<2.0
2.2≤R<9.1
10≤R<22
24≤R≤100k
MCR100
Specifications
1W at 70°C
200V
Limiting element voltage
−55°C to +125°C
Resistance temperature coefficient
(ppm / °C)
(Ω)
±100
(E24,96)
(E24)
500±350
±500
(E24)
±350
(E24)
±200
(E24)
Rev.D
1/3

MCR100JZHJ000 Summary of contents

  • Page 1

    ... Resistors Thick Film Chip Resistors MCR100 (2512 size : 1W) Features 1) Made of same material as the general purpose chip resistors (MCR10 / 18). 2) Highly reliable chip resistor Ruthenium oxide dielectric offers superior resistance to the elements. 3) Electrodes not corroded by soldering Suitable for re-flow soldering. 4) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification. ...

  • Page 2

    ... Resistors Characteristics Item Resistor type J : ±5% Resistance F : ±1% Variation of resistance with temperature ± (2.0%+0.1Ω) Overload A new uniform coating of minimum of 95% of the surface being immersed Solderability and no soldering damage. ± (1.0%+0.05Ω) Resistance to No remarkable abnormality on the appearance. soldering heat ± ...

  • Page 3

    ... Resistors Packaging Reel +1.0 φ180 φ60 13 −1.5 −0 0 Part No. Explanation M C Part No. Packaging Specifications Code Resistance tolerance Part No. Code ± J( 5%) F( MCR100 JZH Reel ( φ 180) : JEITA ET-7200B : Standard product Taping Label W EIAJ ET-7200B compliant 12.0 ± 0.3 (Unit : mm φ13 ± 0.2 φ ...

  • Page 4

    Appendix No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product ...