VARISTOR 75VRMS 14MM RADIAL

S14K75

Manufacturer Part NumberS14K75
DescriptionVARISTOR 75VRMS 14MM RADIAL
ManufacturerEPCOS Inc
SeriesStandarD
S14K75 datasheet
 


Specifications of S14K75

Varistor Voltage120VCurrent-surge4.5kA
Number Of Circuits1Maximum Ac Volts75VAC
Maximum Dc Volts100VDCEnergy20J
Package / CaseDisc 14mmLead Free Status / RoHS StatusLead free / RoHS Compliant
Other names495-2403
B72214S 750K101
B72214S0750K101
B72214S750K101
B72214S750K101V57
S14K75
  
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Page 19/36

Download datasheet (292Kb)Embed
PrevNext
Reliability data
Test
Test methods/conditions
Climatic sequence
CECC 42 000, test 4.16
The specimen shall be subjected to:
a) dry heat at UCT, 16 h
b) damp heat, 1st cycle:
c) cold, LCT, 2 h
d) damp heat, additional 5 cycles:
Then the specimen shall be stored at
room temperature and normal humidity
for 1 to 2 h.
Thereafter, the change of V
measured. Thereafter, insulation resis-
tance R
to CECC 42 000, test 4.8 at V = 500 V.
Fast temperature cycling
IEC 60068-2-14, test Na, LCT/UCT,
dwell time 30 min, 5 cycles
Damp heat, steady state
The specimen shall be subjected to
40 ±2 °C, 90 to 95% r. H. for 56 days
without load / with 10% of the maximum
continuous DC operating voltage V
Then stored at room temperature and
normal humidity for 1 to 2 h.
Thereafter, the change of V
measured. Thereafter, insulation resis-
tance R
to CECC 42 000, test 4.8 at V = 500 V.
Solderability
IEC 60068-2-20, test Ta,
method 1 with modified conditions for
lead-free solder alloys: 245 °C, 3 s:
After dipping the terminals to a depth
of approximately 3 mm from the body
in a soldering bath of 245 °C for 3 s, the
terminals shall be visually examined.
Please read Cautions and warnings and
Important notes at the end of this document.
Leaded varistors
StandarD series
55 °C, 93% r. H., 24 h
55 °C/25 °C, 93% r. H., 24 h/cycle.
shall be
v
shall be measured according
ins
shall be
v
shall be measured according
ins
19
11/07
Requirement
∆V/V (1 mA)
≤10%
|
|
≥1 MΩ
R
ins
∆V/V (1 mA)
≤5%
|
|
No visible damage
∆V/V (1 mA)
≤10%
|
|
≥1 MΩ
R
ins
.
DC
The inspection shall be
carried out under adequate
light with normal eyesight or
with the assistance of a
magnifier capable of giving
a magnification of 4 to
10 times. The dipped sur-
face shall be covered with
a smooth and bright solder
coating with no more than
small amounts of scattered
imperfections such as
pinholes or un-wetted or
de-wetted areas. These
imperfections shall not be
concentrated in one area.