RES 0.0 OHM 1/4W 0805 SMD

ESR10EZPJ000

Manufacturer Part NumberESR10EZPJ000
DescriptionRES 0.0 OHM 1/4W 0805 SMD
ManufacturerRohm Semiconductor
SeriesESR10
ESR10EZPJ000 datasheet
 


Specifications of ESR10EZPJ000

Resistance (ohms)0.0Power (watts)0.25W, 1/4W
CompositionThick FilmFeaturesAnti-Surge
Temperature Coefficient±200ppm/°CToleranceJumper
Size / Dimension0.079" L x 0.049" W (2.00mm x 1.25mm)Height0.022" (0.55mm)
Lead StyleSurface Mount (SMD - SMT)Package / Case0805 (2012 Metric)
Resistance In Ohms0.0Case0805 (2012 metric)
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther namesRHM0.0KTR
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
Page 1/5

Download datasheet (70Kb)Embed
Next
Resistors
Anti-surge Chip Resistors
ESR10 (0805 size : 1 / 4W )
Features
1) Power rating of 1 / 4W (MCR10 1/8W)
2) Superior anti surge to MCR series
3) Highly reliable chip resistor
Ruthenium oxide dielectric offers superior resistance to the elements.
4) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification.
Ratings
Design and specifications are subject to change without notice. Carefully check the specification sheet before using or
ordering it.
Item
Rated power
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70° C .
100
80
60
40
20
0
−55
Rated voltage
The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.
E= P×R
Nominal resistance
See Table 1.
Operating temperature
Conditions
0
70
100
155
AMBIENT TEMPERATURE ( ° C)
Fig.1
E: Rated voltage (V)
P: Rated power (W)
R: Nominal resistance (Ω)
ESR10
Specifications
0.25W (1 / 4W)
at 70°C
Limiting element voltage
150V
−55° C to +155° C
Rev.E
1/4

ESR10EZPJ000 Summary of contents

  • Page 1

    ... Superior anti surge to MCR series 3) Highly reliable chip resistor Ruthenium oxide dielectric offers superior resistance to the elements. 4) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification. Ratings Design and specifications are subject to change without notice. Carefully check the specification sheet before using or ordering it ...

  • Page 2

    ... Resistors Table 1 Resistance range Resistance tolerance (Ω) D (±0.5 (E24) F (±1 10M (E24 10M (E24) J (±5%) Before using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed used with a steady state voltage that is greater than its rated voltage ...

  • Page 3

    ... Resistors Dimensions (Unit : mm 0.3±0.2 0.4±0.2 2.0±0 Packaging Reel +1.0 φ180 φ60 9 −1 No. 3 Resistive element (Oxide metal thick film) 1 Silver thick film electrode 4 2 Nickel electrode 3 Sn electrode 4 Alumina substrate 5 Overcoating (Resin) 6 Taping Heat crimp cover Tape Thick paper ...

  • Page 4

    ... Resistors Part designation E S Part No. Packaging Specifications Code Resistance tolerance Part No. Code ± ± J( 5%) F( 1%) D( ESR10 EZP Reel ( φ 180) : Compatible with JEITA standard "EIAJ ET-7200B" : Standard product Resistance tolerance ± D 0.5% ± ± Packaging specifications ± 0.5%) Paper tape (4mm Pitch) ...

  • Page 5

    Appendix No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product ...