VR25000006813FA500 Vishay, VR25000006813FA500 Datasheet - Page 3

• Manufacturer Part Number: VR25000006813FA500
• Description: RES 681K OHM METL FILM .25W 1%
• Manufacturer: Vishay
• Series: VR25r

Specifications of VR25000006813FA500

• Resistance (ohms): 681K
• Power (watts): 0.25W, 1/4W
• Composition: Metal Film
• Features: Pulse Withstanding
• Temperature Coefficient: ±200ppm/°C
• Tolerance: ±1%
• Size / Dimension: 0.098" Dia x 0.295" L (2.50mm x 7.50mm)
• Lead Style: Through Hole
• Package / Case: Axial
• Resistance In Ohms: 681K
• Case: Axial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Height: -
• Other names: VR25 1% A5 681K

VR25
Vishay BCcomponents
PRODUCTS WITH RADIAL LEADS
Note
• Please refer document number 28721 “Packaging” for more detail
FUNCTIONAL PERFORMANCE
PRODUCT CHARACTERIZATION
Standard values of nominal resistance are taken from the E96/E24/E12 series for resistors with a tolerance of ± 1 %, 5 % or
10 %. The values of the E96/E24/E12 series are in accordance with IEC 60063.
Notes
(1)
• The maximum permissible hot-spot temperature is 155 °C
www.vishay.com
198
DIMENSIONS - RADIAL TAPING
SYMBOL
P
P
P
P
F
W
W
H
H
H
D
L
L
MASS PER UNIT
TYPE
VR25 52 mm
VR25 26 mm
LIMITING VALUES
TYPE
VR25
The maximum voltage that may be continuously applied to the resistor element, see IEC 60115-1
1
0
1
2
1
0
0
0
H
1
Minimum lead wire (tape portion) shortest lead
Feed-hole centre to lead at topside at the tape
H
H
Height of component from tape center
0
1600
Maximum length of snipped lead
Feed-hole center to body center
DC
Minimum hold down tape width
L
For technical questions, contact:
L
1
Lead wire clinch height
Lead-to-lead distance
Pitch of components
Feed-hole diameter
MASS
Component height
(mg)
212
148
Feed-hole pitch
PARAMETER
LIMITING VOLTAGE
Tape width
Metal Glaze Leaded Resistors
High Ohmic/High Voltage
F
U
max.
P
2
P
0
(1)
P
[e-mail]
P
1
MARKING
The nominal resistance and tolerance are marked on the
resistor using four or five colored bands in accordance with
IEC 60062, marking codes for resistors and capacitors.
Yellow and grey are used instead of gold and silver because
metal particles in the lacquer could affect high-voltage
properties.
OUTLINES
The length of the body (L
leads into holes of two identical gauge plates and moving
these plates parallel to each other until the resistor body is
clamped without deformation (IEC 60294).
RMS
1150
D
VALUE
0
12.7
12.7
3.85
6.35
18.0
16.5
19.5
11.0
4.8
5.5
4.0
2.5
29
W
1
0
) is measured by inserting the
LIMITING POWER P
TOLERANCE
W
+ 0.7/- 0
± 1.0
± 0.2
± 0.5
± 1.0
± 0.5
± 0.5
± 0.2
Max.
Document Number: 28732
± 1
-
-
-
0.25
(W)
Revision: 30-Nov-09
70
UNIT
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm