MTU1S1205MC Murata Power Solutions Inc, MTU1S1205MC Datasheet - Page 3

• Manufacturer Part Number: MTU1S1205MC
• Description: DC/DC 1KVDC ISOLAT SMD 1W 12-5V
• Manufacturer: Murata Power Solutions Inc
• Series: MTU1r
• Type: Isolatedr

Specifications of MTU1S1205MC

• Number Of Outputs: 1
• Output: 5V
• Power (watts): 1W
• Mounting Type: Surface Mount
• Voltage - Input: 12V
• Package / Case: 5-SMD Module
• 1st Output: 5 VDC @ 200mA
• Size / Dimension: 0.331" L x 0.323" W x 0.335" H (8.4mm x 8.2mm x 8.5mm)
• Operating Temperature: -40°C ~ 85°C
• Power (watts) - Rated: 1W
• Efficiency: 84%
• Approvals: UL
• Output Power: 1 W
• Input Voltage Range: 10.8 V to 13.2 V
• Input Voltage (nominal): 12 V
• Output Voltage (channel 1): 5 V
• Output Current (channel 1): 200 mA
• Isolation Voltage: 1 KV
• Package / Case Size: 8.4 mm x 8.2 mm x 8.5 mm
• Output Type: DC/DC Converter
• Output Voltage: 5 V
• Product: Isolated
• Dc / Dc Converter O/p Type: Single
• No. Of Outputs: 1
• Input Voltage: 12V
• Power Rating: 1W
• Output Current: 200mA
• Supply Voltage: 12V
• Dc / Dc Converter Case Style: SMD
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 811-2254-5

APPLICATION NOTES
www.murata-ps.com
Minimum load
The minimum load to meet datasheet specifi cation is 10% of the full rated load across the specifi ed input voltage range. Lower than 10% minimum loading will result in
an increase in output voltage, which may rise to typically double the specifi ed output voltage if the output load falls to less than 5%.
Capacitive loading and start up
Typical start up times for this series, with a typical input voltage rise time of 2.2μs and output capacitance of 10μF, are shown in the table below. The product
series will start into a capacitance of 47μF with an increased start time, however, the maximum recommended output capacitance is 10μF.
Ripple & Noise Characterisation Method
Ripple and noise measurements are performed with the following test confi guration.
Differential Mode Noise Test Schematic
C1
C2
C3
R1
R2
T1
RLOAD
Measured values are multiplied by 10 to obtain the specifi ed values.
1μF X7R m ultilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC/DC converter
10μF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC/DC converter with an ESR of less
than 100mΩ at 100 kHz
100nF multilayer ceramic capacitor, general purpose
450Ω resistor, carbon fi lm, ±1% tolerance
50Ω BNC termination
3T of the coax cable through a ferrite toroid
Resistive load to the maximum power rating of the DC/DC converter. Connections should be made via twisted wires
MTU1S0505MC
MTU1S0509MC
MTU1S0512MC
MTU1S0515MC
MTU1S1205MC
MTU1S1209MC
MTU1S1212MC
MTU1S1215MC
SUPPLY
Start-up time
DC/DC Converter
Input
0.9
2.7
4.3
7.5
0.9
1.9
3.3
4.7
+
-
ms
Output
+
-
C1 C2 C3
R LOAD
R1
T1
Technical enquiries email: [e-mail], tel: [phone]
Isolated 1W Single Output SM DC/DC Converters
R2
OSCILLOSCOPE
Y INPUT
Typical Start-Up Wave Form
2011-02-01 KDC_MTU.A03 Page 3 of 6
MTU1 Series