YC248-JR-07820KL Yageo, YC248-JR-07820KL Datasheet

Page 1

... DATA SHEET ARRAY CHIP RESISTORS YC248 (16Pin/8R) 5%, 1% sizes 0616 RoHS compliant ...

Page 2

... GLOBAL PART NUMBER ( PREFERRED YC248 – XXXX L (1) (2) (3) (4) (5) ( TOLERANCE F = ± ±5% (for Jumper ordering, use code PACKAGING TYPE R = Paper taping reel K = Embossed taping reel ( 3 ) TEMPERATURE COEFFICIENT OF RESISTANCE – = Base on spec ( 4 ) TAPING REEL inch dia. Reel ( 5 ) RESISTANCE VALUE There are 2~4 digits indicated the resistor value. Letter R/K/M is decimal point, no need to mention the last zero after R/K/M, e.g.1K2, not 1K20. Detailed resistance rules show in table of “ ...

Page 3

... RDERING EXAMPLE The ordering code of a ARV381 resistor, value 1,000 X with ±5% tolerance, supplied in tape of 5,000 units per reel is: 235005310102(L) or YC248-JR-071K(L). NOTE 1. All our RSMD products are RoHS compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" customized label, "LFP" or specific symbol printed and the optional "L" at the end of GLOBAL PART NUMBER / 12NC can be added (both are on customer request) Oct 31, 2008 V ...

Page 4

... First two digits for significant figure and 3rd digit for number of zeros Fig. 3 Chip resistor outlines H B Fig. 4 YC248 series chip resistors dimension R1=R2=R3=R4=R5=R6=R7=R8 Product specification overcoat resistive layer inner electrode termination ceramic substrate YNSC069 CCB261_b For dimension see Table handbook, 2 columns ...

Page 5

... Where V=Continuous rated (rms) working voltage (V) P=Rated power (W) R=Resistance value (X) Oct 31, 2008 V.2 YC SERIES 248 (RoHS Compliant) YC248 1/16 W –55 °C to +155 ° 100 V 100 (E24) 10 Ω MΩ 1% (E24/E96) 10 Ω MΩ < 0.05 Ω Zero Ohm Jumper ± ...

Page 6

... Ohmic value checked during bending 6 Product specification 8 REQUIREMENTS ±(2%+0.05 Ω) ±(1%+0.05 Ω) ±(2%+0.05 Ω) ±(0.5%+0.05 Ω) for 10 KΩ MΩ ±(1%+0.05 Ω) for others ±(2%+0.05 Ω) No visible damage ±(1%+0.05 Ω) No visible damage www.yageo.com ...

Page 7

... Leadfree solder, 260 °C, 30 seconds immersion time Condition B, no pre-heat of samples Leadfree solder, 270 °C, 10 seconds immersion time Procedure 2 for SMD: devices fluxed and cleaned with isopropanol 7 Product specification 8 REQUIREMENTS Well tinned (≥95% covered) No visible damage No visible damage ±(1%+0.05 Ω) No visible damage www.yageo.com ...

Page 8

... PCN.” Oct 31, 2008 V.2 YC SERIES 248 (RoHS Compliant) DESCRIPTION - Change to dual brand datasheet that describes YC248 with RoHS compliant - Description of "Halogen Free Epoxy" added - Define global part number - New datasheet for 0616 (16Pin/8R) chip resistor arrays 1% and 5% with lead-free terminations - Replace the 0616 part of pdf files: ARV381_5_3 ...