CRB2A4E150JT AVX Corporation, CRB2A4E150JT Datasheet - Page 3

• Manufacturer Part Number: CRB2A4E150JT
• Description: RES ARRAY 15 OHM 5% 0804
• Manufacturer: AVX Corporation
• Series: CRB, Kyocerar

Specifications of CRB2A4E150JT

• Temperature Coefficient: ±250ppm/°C
• Resistance (ohms): 15
• Number Of Resistors: 4
• Circuit Type: Isolated
• Tolerance: ±5%
• Power Per Element: 62.5mW
• Number Of Pins: 8
• Package / Case: 0804 (2010 Metric), Concave
• Size / Dimension: 0.079" L x 0.039" W (2.00mm x 1.00mm)
• Height: 0.016" (0.40mm)
• Mounting Type: Surface Mount
• Operating Temperature: -55°C ~ 125°C
• Resistance: 15ohm
• Resistance Tolerance: ± 5%
• Power Rating: 63mW
• Voltage Rating: 50V
• No. Of Elements: 4
• Resistor Case Style: SMD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chip Resistor Arrays
CR, CJ, CRA, CRB, CRC Series - Test Conditions
MECHANICAL CHARACTERISTICS
ENVIRONMENTAL CHARACTERISTICS
10
Anti-Vibration
Temperature
Temperature
Temperature
Loading Life
Resistance
Resistance
Resistance
in Moisture
Soldering
Moisture
Terminal
Strength
Life Test
Storage
Storage
Solvent
Cycle
Heat
Test
High
Low
Solderability
Item
Item
Visual
Visual
Visual
Visual
Visual
Visual
Visual
Visual
Visual
Visual
R/R
R/R
R/R
R/R
R/R
R/R
R/R
R/R
R/R
R/R
No evidence of mechanical damage after loading
±(0.5%+0.05Ω) max.
±(1%+0.05Ω) max.
±(1%+0.05Ω) max.
±(1%+0.05Ω) max.
No evidence of leaching
Coverage ≥95% each termination end
No evidence of mechanical damage
No evidence of mechanical damage
No evidence of mechanical damage
±(1%+0.1Ω) max.
±(2%+0.1Ω) max.
±(3%+0.1Ω) max.
±(3%+0.1Ω) max.
±(3%+0.1Ω) max.
±(3%+0.1Ω) max.
of the initial value
of the initial value
of the initial value
of the initial value
of the initial value
of the initial value
of the initial value
of the initial value
of the initial value
of the initial value
No evidence of mechanical damage
No evidence of mechanical damage
No evidence of mechanical damage
No evidence of mechanical damage
No evidence of mechanical damage
Resistor
Resistor
Standard
Standard
50mΩ max.
50mΩ max.
50mΩ max.
50mΩ max.
50mΩ max.
50mΩ max.
50mΩ max.
50mΩ max.
50mΩ max.
50mΩ max.
Jumper
Jumper
Bending in
10 seconds
Apply the load as shown:
Measure resistance during load application
PC Board = Glass epoxy t = 1.60 (0.063)
Immerse into molten solder at 260±5°C for 10±1 sec.
Stabilize component at room temperature for 1 hr.
Measure resistance.
Immerse in Rogin Flux for 2±0.5 sec. and in
SN62 solder at 235±5°C for 2±0.5 sec.
2 hrs. each in X, Y and Z axis. (TTL 6 hrs.) 10 to 55 Hz
sweep in 1 min. at 1.5mm amplitude.
Immerse in static state butyl acetate at 20°C to 25°C
for 30±5 sec.
Stabilize component at room temperature for 30 min.
then measure value.
(1) Run 5 cycles as follows: -55±3°C for 30 min.
(2) Stabilize component at room temperature for 1 hr.
(1) Dwell in -55°C chamber without loading for 1000
(2) Stabilize component at room temperature for 1 hr.
(1) Dwell in 125°C chamber without loading for 1000
(2) Stabilize component at room temperature for 1 hr.
(1) Dwell in temp.: 65°C RH90 to 95% RH chamber
(2) Stabilize component at room temperature for 1 hr.
(1) Temp.: 70±3°C Voltage: (rated voltage) on 90 min.
(2) Stabilize component at room temperature for 1 hr.
(1) Temp.: 40±2°C RH: 90-95% Voltage Cycle: on 90
(2) Stabilize component at room temperature for 1 hr.
125±3°C for 30 min. Room temp. for 10-15 min.
then measure value.
hrs.
then measure value.
hrs.
then measure value.
without loading for 1000
then measure value.
off 30 min. Duration: 1000
then measure value.
min. (rated voltage) off 30 min. Duration: 1000
then measure value.
R230
Resistor
Resistor
(0.787)
20
(1.969)
50
Test Conditions
Test Conditions
+48
-0
[φ5 (0.197)]
+48
-0
hrs.
hrs.
45 (1.772) 45 (1.772)
Jumper
Jumper
millimeters (inches)
±2 (0.079)max
+48
-0
hrs.
+48
-0
+48
-0