AD6630AR Analog Devices Inc, AD6630AR Datasheet - Page 3

• Manufacturer Part Number: AD6630AR
• Description: IC IF GAIN BLOCK W/CLAMP 16-SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD6630AR

• Rohs Status: RoHS non-compliant
• Current - Supply: 30mA ~ 48mA
• Frequency: 250MHz
• Gain: 22dB ~ 24dB @ 250MHz
• Noise Figure: 4dB
• P1db: 7.5dBm
• Package / Case: 16-SOIC (0.300", 7.50mm Width)
• Test Frequency: 250MHz
• Voltage - Supply: 8.5V ~ 10.5V
• Rf Type: -

Parameter
HIGH LEVEL CLAMP MAXIMUM OUTPUT @ 250 MHz
PHASE VARIATION
CMRR
PSRR
NOTES
1
2
3
4
5
6
7
8
Specifications subject to change without notice.
Model
AD6630AR
AD6630AR-REEL
AD6630R/PCB
REV. 0
ABSOLUTE MAXIMUM RATINGS
Parameter
Single Supply Voltage
Positive Supply Voltage
Negative Supply Voltage
Input Power
Storage Temperature
Junction Temperature
ESD Protection
All specifications are valid across the operating frequency range when the source and load impedance are a conjugate match to the amplifier’s input and output
Test is for two tones separated by 1 MHz for IFs at 70 MHz and 250 MHz at –23 dBm per tone input.
Low Level Clamp is selected by connecting pin CLLO to the negative supply, while pin CLHI is left floating. Clamping can be set at lower levels by connecting pin
High Level Clamp is selected by connecting pin CLHI to the negative supply, while pin CLLO is left floating, this allows the maximum linear range of the device to
Output clamp levels are measured for hard clamping with a +3 dBm input level. Valid for a maximum input level of +8 dBm/200
Measured as the change in output phase when the input level is changed from –53 dBm to +8 dBm (i.e., from linear operation to clamping).
Ratio of the differential output signal (referenced to the input) to the common-mode input signal presented to all input pins.
Ratio of signal on supply to differential output (<500 kHz).
impedance.
CLLO and CLHI to the negative supply through an external resistor.
be utilized.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD6630 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
8
7
6
Min
–0.5
–0.5
–65
1
–40 C to +85 C (Ambient)
–40 C to +85 C (Ambient)
Temperature Range
–5.75
Max
11.5
5.75
0.5
+8
+150
+150
ORDERING GUIDE
Units
V
V
V
dBm
kV
C
C
4, 5
–3–
EXPLANATION OF TEST LEVELS
I.
II. 100% production tested at +25 C, and guaranteed by
III. Sample tested only.
IV. Parameter guaranteed by design and analysis.
V. Parameter is typical value only.
VI. 100% production tested at +25 C, and sample tested at
Temp
Full
+25 C
+25 C
+25 C
Package Description
16-Lead Wide Body SOIC
AD6630AR on 1000 PC Reel
Evaluation Board with AD6630AR
100% production tested.
design and analysis at temperature extremes.
temperature extremes.
Test
Level
IV
V
V
V
Min
WARNING!
= 3.2 V p-p—differential.
Typ
11.2
9
50
30
Package Option
R-16
ESD SENSITIVE DEVICE
Max
12.2
AD6630
Units
dBm
Degree
dB
dB