UPC2763TB-E3 CEL, UPC2763TB-E3 Datasheet - Page 6

• Manufacturer Part Number: UPC2763TB-E3
• Description: 3V MMIC AMPLIFIER 2.9GHZ SOT363
• Manufacturer: CEL

Specifications of UPC2763TB-E3

• Current - Supply: 27mA ~ 35mA
• Frequency: 2.3GHz ~ 2.7GHz
• Gain: 18dB ~ 24dB
• Noise Figure: 5.5dB ~ 7.5dB
• P1db: 4dBm ~ 6.5dBm
• Package / Case: SC-70-6, SC-88, SOT-363
• Rf Type: Cellular, GPS, PCS
• Test Frequency: 1.9GHz
• Voltage - Supply: 2.7V ~ 3.3V
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: UPC2763TB-E3TR; UPC2763TB-TR; UPC2763TBTR

Note:
Embossed Tape, 8 mm wide. Pins 1, 2 and 3 face perforated side
of tape.
PIN DESCRIPTIONS
Life Support Applications
These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably
be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and
agree to fully indemnify CEL for all damages resulting from such improper use or sale.
OUTLINE DIMENSIONS
ORDERING INFORMATION
2.0±0.2
Pin No.
PART NUMBER
UPC2763TB-E3-A
1
4
6
2
3
5
0.9 ± 0.1
DATA SUBJECT TO CHANGE WITHOUT NOTICE
1.3
CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • [phone] • Telex 34-6393 • FAX [phone]
0.7
0.65
0.65
EXCLUSIVE NORTH AMERICAN AGENT FOR
3
2
1
Pin Name
Output
Input
GND
PACKAGE OUTLINE S06
V
CC
2.1±0.1
1.25±0.1
0 ~0.1
24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) • Internet: http://WWW.CEL.COM
Voltage (V)
2.7 to 3.3
(Units in mm)
Applied
–
0
3K/Reel
QTY
DOT ON
BACK SIDE
4
5
6
0.15
Signal input pin. An internal matching circuit, configured with
resistors, enables 50 Ω connection over a wide bandwidth. A
multi-feedback circuit is designed to cancel the deviations of
h
source with a blocking capacitor.
Signal output pin. Connect an inductor between this pin and
V
Power supply pin. This pin should be externally equipped with
a bypass capacitor to minimize ground impedance.
Ground pins. These pins should be connected to system
ground with minimum inductance. Ground pattern on the board
should be formed as wide as possible. All the ground pins
must be connected together with wide ground pattern to
minimize impedance difference.
0.2
FE
CC
+0.1
-0.5
+0.1
and resistance. This pin must be coupled to the signal
-0
to supply current to the internal output transistors.
RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS
Description
LEAD CONNECTIONS
1. INPUT
2. GND
3. GND
4. OUTPUT
5. GND
6. V
3
2
1
CC
(Top View)
4
5
6
4
5
6
1
Internal Equivalent
(Bottom View)
3
Circuit
06/21/2000
2
1
3
2
5
6
4