1004-TCB1D434 Silicon Laboratories Inc, 1004-TCB1D434 Datasheet - Page 15

• Manufacturer Part Number: 1004-TCB1D434
• Description: BOARD EVALUATION FOR SI1004
• Manufacturer: Silicon Laboratories Inc
• Type: Transceiver, ISMr

Specifications of 1004-TCB1D434

• Mfg Application Notes: SI1000 Code Examples AppNote
• Frequency: 434MHz
• Supply Voltage (min): 0.9 V
• Product: RF Modules
• Maximum Frequency: 915 MHz
• Output Power: 13 dBm
• Antenna: SMA
• Supply Voltage (max): 3.6 V
• For Use With/related Products: Si100x
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 336-1889

10.2. Target Board Power Options and Current Measurement
The Si10xx Target Board supports three power options, selectable by the three-way header (J10/J11). The power
options vary based on the configuration (one-cell or two-cell mode) selected by SW4. Power to the MCU may be
switched on/off using the power switch (SW5). Important Note: The power switch (SW5) must be in the OFF
position prior to switching between one-cell and two-cell mode using SW4. The power options are described
in the paragraphs below.
10.2.1. Wall Power
When the J10/J11 three-way header is set to WALL_PWR, the Si10xx Motherboard may be powered from the
following power sources:



All the three power sources are ORed together using reverse-biased diodes (D1, D2, D3), eliminating the need for
headers to choose between the sources. The target board will operate as long as any one of the power sources is
present. The ORed power is regulated to a 3.3 V dc voltage using a LDO regulator (U2). The output of the regulator
powers the +3 VD net on the target board.
If SW4 is configured to select two-cell mode, the VBAT supply net on the target board is powered directly from the
+3 VD net. If SW4 is configured to select one-cell mode, the VBAT supply net is powered directly from the +1 VD.
This power supply net takes +3 VD and passes it through a 1.65 V LDO. The LDO’s output voltage is variable and
can be set by changing the value of resistor R32.
10.2.2. AAA Battery
When the J10/J11 three-way header is set to AAA_BAT, the Si10xx Target Board may be powered from a single
AAA battery inserted in BT1 or from the series combination of the AAA batteries inserted in BT1 and BT2. A single
battery is selected when SW4 is configured to one-cell mode. The two AAA batteries configured in series to provide
a voltage of ~3 V are selected when SW4 is configured to two-cell mode.
10.2.3. Coin Cell Battery
When the J10/J11 three-way header is set to COIN_CELL, the Si10xx Target Board may be powered from a single
1.5 V Alkaline (A76) or Silver Oxide (357) button cell inserted in BT4 or from a single 3 V Lithium (CR2032) coin
cell inserted in BT3. The button cell (BT4) is selected when SW4 is configured to one-cell mode, and the coin cell
(BT3) is selected when SW4 is configured to two-cell mode.
10.2.4. Measuring Current
The header (J17) and terminal block (H2) provide a way to measure the total supply current flowing from the power
supply source to the MCU. The measured current does not include any current from the VBAT LED (DS2), the
address latch (U4) or the quiescent current from the power supply; however, it does include the current used by
any LEDs powered from the VDD/DC+ supply net or sourced through a GPIO pin. See the target board schematic
in Figure 11 through Figure 13 for additional information.
9 VDC power using the ac to dc power adapter (P2)
5 VDC USB VBUS power from PC via the USB Debug Adapter (J9)
5 VDC USB VBUS power from PC via the CP2103 USB connector (P3)
AAA_BAT
AAA_BAT
AAA_BAT
COIN_CELL
WALL_PWR
COIN_CELL
WALL_PWR
COIN_CELL
WALL_PWR
Rev. 0.1
J11
J11
J11
VBAT
VBAT
VBAT
Si10xx-DK
15