ATR2732N1-PBQW Atmel, ATR2732N1-PBQW Datasheet
ATR2732N1-PBQW
Specifications of ATR2732N1-PBQW
Related parts for ATR2732N1-PBQW
ATR2732N1-PBQW Summary of contents
Page 1
... Atmel ’s silicon-germanium BiCMOS process (SiGMOS). The ATR2732N1 carries out all functions of RF and IF processing, as well as the clock-signal generation for these functions. Therefore, there is an integrated fractional PLL, which, equivalent to most of the other functions, can be controlled via an external digital bus. The RF functions include LNA, down-conversion mixing, amplifying, detec- tion, and gain control ...
Page 2
... Figure 1-1. Block Diagram 2. Pin Configuration Figure 2-1. Pinning QFN64 VAMIXL VAVCOL TUNVL GDVCOL LNAVIN+ LNAVL+ LNAVL- LNAVIN- VALNA LNALO+ LNALO- AGCRF GNDLNA LNALIN+ LNALIN- IPINDIO ATR2732N1 2 Gain cntl Vtune gen. L-band VCO PLL VHF VCO frac. PLL QFN64 PWR RSSI ...
Page 3
... Reference-tank connection for to generate the tuning voltages for the external VHF filters (varactors) 40 TNKREFO Reference-tank connection for to generate the tuning voltages for the external VHF filters (varactors) 41 PFDOUTV Output-of-phase comparator for VHF VCO (connected to PLL loop filter) 9130AS–DAB–04/08 ATR2732N1 3 ...
Page 4
... Connection for reference clock crystal 60 VDD Supply for digital circuits 61 PFDOUTL Output of phase comparator for VCO for L-band (connected to PLL loop filter) 62 GDMIXL Ground (L-band mixer) 63 MILIN+ (Differential) Input of L-band mixer – 64 MILIN (Differential) Input of L-band mixer Paddle GND Ground ATR2732N1 4 9130AS–DAB–04/08 ...
Page 5
... Functional Description The ATR2732N1 front-end IC was developed as a tuner IC for DAB reception. It was designed for operation in L-band (1452 MHz to 1492 MHz) and VHF BIII (167 MHz to 240 MHz). The front end contains gain-controlled LNAs, an L-band mixer with a corresponding PLL, and a VHF-band mixer with a fractional PLL ...
Page 6
... Figure 3-1. 3.2 AGC in General There are three AGCs in the ATR2732N1, one for the RF signals (around the LNAs) (1) and (3), one for the very beginning of the IF path (mainly VHF mixer), and one for the IF amplifiers (5) down to the output to baseband (7). In these AGCs, the output signals of the relevant blocks are amplified, weakly band-pass fil- tered, rectified, and, finally, low-pass filtered ...
Page 7
... RSSI Measurement The ATR2732N1 offers the option of getting information about the field strength. This is not an absolute real-field-strength value, but an indication of in which range the field strength is avail- able. This information can be obtained from the 8 low bits of the status register. ...
Page 8
... IF frequency of 38.912 MHz for VHF or converted L-band signal is done by an additional on-chip VCO using an internal fractional-N PLL. Due to the digital tuning option of the reference frequency, the ATR2732N1 is able to support the single reference clock design if the baseband can support such a feature (as the ATR2740 does) ...
Page 9
... There are 16 registers. Fourteen of them are used to control the ATR2732N1. The two others, registers 15 and 16, are Test Mode Registers. All these registers need to be reset by writing “0” ...
Page 10
... Storage temperature Maximum RF input power VHF Maximum RF input power L-band Notes: 1. The part may not survive all maximums applied simultaneously! 5. Thermal Resistance Parameters Junction, case 6. Operating Range Parameters Supply voltage Ambient temperature ATR2732N1 10 Symbol Value V 4 –40 to +100 c T –40 to +150 ...
Page 11
... Electrical Characteristics Test conditions (if not otherwise specified): V No. Parameters Test Conditions 1 Power Supply Supply voltage of front 1.1 end ATR2732N1 Supply voltage of 1.2 baseband processor 1.3 Leakage current, all off 2 Power Control 2.1 Power on/off delay 2.2 Power off/on delay Supply current L-band 2 ...
Page 12
... L-band Operation 9.1 Frequency range 8 dB SNR at IF output 9.4 Sensitivity to baseband, measured with sample application Maximum input power 9.5 level *) Type means 100% tested 100% correlation tested Characterized on samples Design parameter ATR2732N1 12 = +3.3V +25°C, 50Ω input match CC amb Pin Symbol 46 Rfin f Rfin Min ...
Page 13
... Ordering Information Extended Type Number ATR2732N1-PBQW ATR2732N1-PBPW 9. Package Information Package: VQFN_ 9 x 9_64L Exposed pad 5.8 x 5.8 Dimensions in mm Not indicated tolerances ±0.05 Top 64 1 Pin 1 identification 16 Drawing-No.: 6.543-5119.01-4 Issue: 1; 31.05.05 9130AS–DAB–04/08 Package Remarks 9 mm × 9 mm, 0.5 mm pitch, lead-free QFN64 9 mm × ...
Page 14
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...