ATZB-24-B0R Atmel, ATZB-24-B0R Datasheet
ATZB-24-B0R
Specifications of ATZB-24-B0R
Available stocks
Related parts for ATZB-24-B0R
ATZB-24-B0R Summary of contents
Page 1
... ZigBit™ 2.4 GHz Wireless Modules .................................................................................................................... ATZB-24-A2/B0 Datasheet 8226B–MCU Wireless–06/09 ...
Page 2
ZigBit™ 2.4 GHz Wireless Modules 1-2 8226B–MCU Wireless–06/09 ...
Page 3
... Approved Antenna List..................................................................................................... 4-23 Section 5 5.1 Ordering Information ........................................................................................................ 5-24 ZigBit™ 2.4 GHz Wireless Modules Absolute Maximum Ratings ................................................................................. 3-7 Test Conditions.................................................................................................... 3-7 RF Characteristics ............................................................................................... 3-8 ATmega1281V Microcontroller Characteristics ................................................... 3-8 Module Interfaces characteristics ........................................................................ 3-8 General recommendations ................................................................................ 3-16 ATZB-24-B0....................................................................................................... 3-17 ATZB-24-A2....................................................................................................... 3-19 i 8226B–MCU Wireless–06/09 ...
Page 4
... RF development, and shortens time to market for a wide range of wireless applications. Two different versions of 2.4 GHz ZigBit modules are available: ATZB-24-B0 module with balanced RF port for applications where the benefits of PCB or external antenna can be utilized and ATZB-24-A2 module with dual chip antenna satisfying the needs of applications requiring integrated, small-footprint antenna design ...
Page 5
... Key Features • Ultra compact size (24 x 13.5 x 2.0 mm for ATZB-24-A2 module and 18.8 x 13.5 x 2.0 mm for ATZB-24-B0 module) • Innovative (patent-pending) balanced dual chip antenna design with antenna gain of approximately 0 dBi (for ATZB-24-A2 version) • High RX sensitivity (-101 dBm) • ...
Page 6
DTR DIP EEPROM ESD GPIO HAL HVAC IEEE IRQ ISM JTAG MAC MCU NWK OEM OTA PCB PER PHY RAM RF RTS/CTS RX SMA SPI SW TTM TX UART USART USB ZDK ZigBee, ZigBee PRO 802.15.4 ...
Page 7
... Related Documents [1] Atmel 8-bit AVR Microcontroller with 64K/128K/256K Bytes In-System Programmable Flash. 2549F AVR 04/06 [2] Atmel Low-Power Transceiver for ZigBee Applications. AT86RF230 datasheet. doc5131.pdf [3] IEEE Std 802.15.4-2003 IEEE Standard for Information technology - Part 15.4 Wireless Medium Access Control (MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs) [4] ZigBee Specification ...
Page 8
... Based on a solid combination of Atmel’s latest MCU Wireless hardware platform [1], the ZigBit offers superior radio performance, ultra-low power consumption, and exceptional ease of integration. Figure 2-1. ATZB-24-B0 Block Diagram USART/SPI ANALOG Figure 2-2. ATZB-24-A2 Block Diagram USART/SPI ZigBit™ 2.4 GHz Wireless Modules V (1.8 - 3.6V) CC IRQ ...
Page 9
... GHz frequency band. To jumpstart evaluation and development, Atmel also offers a complete set of evaluation and develop- ment tools. The ZigBit Development Kit [6] (ATZB-DK-24) comes with everything you need to create custom applications featuring ZigBit module. The kit features MeshBean development boards with an easy-to-access extension connector for attach- ing third party sensors and other peripherals, and a JTAG connector for easy application uploading and debugging ...
Page 10
Electrical Characteristics 3.1.1 Absolute Maximum Ratings Table 3-1. Absolute Maximum Ratings Voltage on any pin, except RESET with respect to Ground DC Current per I/O Pin DC Current DVCC and DGND pins Input RF Level Notes: 1. Absolute Maximum ...
Page 11
Current consumption actually depends on multiple factors, including but not limited to, the board design and materials, BitCloud settings, network activity, EEPROM read/write operations. It also depends on MCU load and/or peripherals used by an application. 3.1.3 RF Characteristics Table ...
Page 12
... Parameters Size Weight Operating Temperature Range Operating Relative Humidity Range Note: 1. Minor degration of clock stability may occur. Figure 3-1. ATZB-24-B0 Mechanical drawing Figure 3-2. ATZB-24-A2 Mechanical drawing ZigBit™ 2.4 GHz Wireless Modules Value 18.8 x 13.5 x 2.0 mm 24.0 x 13.5 x 2.0 mm 1.3g 1.5g -20° ...
Page 13
... Pin Configuration Figure 3-3. ATZB-24-B0 Pinout Figure 3-4. ATZB-24-A2 Pinout ZigBit™ 2.4 GHz Wireless Modules Specifications 3-10 8226B–MCU Wireless–06/09 ...
Page 14
Table 3-6. Pin descriptions Connector Pin 9,22, 24, ZigBit™ 2.4 GHz ...
Page 15
Table 3-6. Pin descriptions Connector Pin 44,46, Notes: 1. The UART_TXD pin is intended for input (i.e. its designation as "TXD" implies some complex system containing ZigBit as its ...
Page 16
... Using ferrite bead and 1 µF capacitor located closely to the power supply pin is recommended, as shown below. 10. Pins 44 through 48 are not designed for the ATZB-24-A2 module. Note these pins are used in ATZB-24-B0, see them in antenna schematics below. 11. In SPI mode, USART0_EXTCLK is output. In USART mode, this pin can be configured as either input or output pin. ZigBit™ ...
Page 17
... Figure 3-5. ATZB-24-B0 PCB Recommended Layout, Top View Figure 3-6. ATZB-24-A2 PCB Recommended Layout, Top View ZigBit™ 2.4 GHz Wireless Modules Specifications 3-14 8226B–MCU Wireless–06/09 ...
Page 18
... These antenna reference designs are recommended for successful design-in. Figure 3-7. PCB Layout: Symmetric Dipole Antenna recommended for ATZB-24-B0 The symmetric dipole antenna above has been tuned for the particular design. The 'cut-and-paste' approach would not guarantee optimal performance because of multiple factors affecting proper antenna ZigBit™ ...
Page 19
The particular factors are the board material and thickness, shields, the material used for enclosure, the board neighborhood, and other components adjacent to antenna. 3.5.1 General recommendations Metal enclosure should not be used. Using low ...
Page 20
... Antenna specifications 3.6.1 ATZB-24-B0 Figure 3-8. Symmetric Dipole Antenna Pattern (horizontal and vertical plane) for ATZB-24-B0 ZigBit™ 2.4 GHz Wireless Modules Specifications ATZB-24-B0: ATZB-24-B0 ATZB-24-B0: 8226B–MCU Wireless–06/09 3-17 ...
Page 21
... Figure 3-9. PCB Layout with 50 Ohm External Antenna recommended for ATZB-24-B0 In case the external unbalanced 50 Ohm antenna is required, it can be easily interfaced to ATZB-24-B0 module by using 2:1 balun as shown above. The reference design in use SMA connector. Figure 3-10. SMA connectors ZigBit™ 2.4 GHz Wireless Modules ...
Page 22
... ATZB-24-A2 Figure 3-11. Symmetric Dipole Antenna Pattern (horizontal and vertical plane) for ATZB-24-A2 Note: The antenna patterns presented above were observed using PCB enhanced with legs made of original nylon. ZigBit™ 2.4 GHz Wireless Modules Specifications ATZB-24-A2: ATZB-24-A2 ATZB-24-A2: 3-19 ...
Page 23
... Figure 3-12. PCB Layout with Dual Chip Antenna Module recommended for ATZB-24-A2 Normally, chip antennas are more tolerant of the board or enclosure materials in ZigBit's neighborhood as well. However, general recommendations given above for the PCB antenna design still apply. The board design should prevent propagation of microwave field inside the board material. Electromag- netic waves of high frequency may penetrate the board thus making the edges of the board radiate, which may distort the antenna pattern ...
Page 24
... Any similar wording that expresses the same meaning may be used used with the ATZB-24-B0 module, the external antennas have been tested and approved which are specified in here below. The ATZB-24-B0 Module may be integrated with other custom design antennas which OEM installer must authorize following the FCC 15 ...
Page 25
... CANADA (IC) Equipment is subject to certification under the applicable RSSs, shall be permanently labelled on each item inseparable combination. The label must contain the following information for full compliance: For ATZB-24-A2 module: Certification Number: Manufacturer's Name, Trade Name or Brand Name: Model Name: For ATZB-24-B0 module: ...
Page 26
... ATZB-24-A2 Module works with integrated dual chip antenna. The design of the antenna is fully compli- ant with all the aforementioned regulation. ATZB-24-B0 Module has been tested and approved for use with the antennas listed in the table below. ATZB-24-0B Module may be integrated with other custom design antennas which OEM installer must authorize with respective regulatory agencies ...
Page 27
... Ordering Information Part Number ATZB-24-B0R ATZB-24-A2R Note: Tape&Reel quantity: 200 ZigBit™ 2.4 GHz Wireless Modules Ordering Information Description 2.4 GHz IEEE802.15.4/ZigBee OEM Module w/ Balanced RF Port 2.4 GHz IEEE802.15.4/ZigBee OEM Module with dual chip antenna Section 5 5-24 8226B–MCU Wireless–06/09 ...
Page 28
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...