XBP24-AWI-001 Digi International/Maxstream, XBP24-AWI-001 Datasheet - Page 7

• Manufacturer Part Number: XBP24-AWI-001
• Description: MODULE 802.15.4 100MW WIRE ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-AWI-001

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 20dBm (100mW)
• Sensitivity: -100dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Current - Transmitting: 215mA @ 3.3V
• Data Interface: PCB, Through Hole
• Antenna Connector: On-Board, Wire Whip
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -

XBee®/XBee‐PRO® RF Modules ‐ 802.15.4 ‐ v1.xEx [2009.09.23]
Pin Signals
Figure 1‐03. XBee®/XBee‐PRO® RF Module Pin
(top sides shown ‐ shields on bottom)
Table 1‐02. Pin Assignments for the XBee and XBee‐PRO Modules
* Function is not supported at the time of this release
Design Notes:
© 2009 Digi Internatonal, Inc.
Pin #
• Minimum connections: VCC, GND, DOUT & DIN
• Minimum connections for updating firmware: VCC, GND, DIN, DOUT, RTS & DTR
• Signal Direction is specified with respect to the module
• Module includes a 50k Ω pull-up resistor attached to RESET
• Several of the input pull-ups can be configured using the PR command
• Unused pins should be left disconnected
10
12
13
14
15
16
17
18
19
20
11
1
2
3
4
5
6
7
8
9
Numbers
(Low‐asserted signals are distinguished with a horizontal line above signal name.)
DTR / SLEEP_RQ / DI8
Associate / AD5 / DIO5
RTS / AD6 / DIO6
DIN / CONFIG
PWM0 / RSSI
ON / SLEEP
CTS / DIO7
AD4 / DIO4
AD3 / DIO3
AD2 / DIO2
AD1 / DIO1
AD0 / DIO0
[reserved]
RESET
Name
PWM1
DOUT
VREF
DO8*
GND
VCC
Direction
Output
Output
Output
Output
Output
Either
Either
Either
Either
Either
Either
Either
Either
Input
Input
Input
Input
-
-
-
Pin 10
Pin 1
Request-to-Send Flow Control, Analog Input 6 or Digital I/O 6
Module Reset (reset pulse must be at least 200 ns)
Associated Indicator, Analog Input 5 or Digital I/O 5
PWM Output 0 / RX Signal Strength Indicator
Clear-to-Send Flow Control or Digital I/O 7
Pin Sleep Control Line or Digital Input 8
Voltage Reference for A/D Inputs
Analog Input 4 or Digital I/O 4
Analog Input 3 or Digital I/O 3
Analog Input 2 or Digital I/O 2
Analog Input 1 or Digital I/O 1
Analog Input 0 or Digital I/O 0
Module Status Indicator
Pin 20
Pin 11
UART Data Out
Digital Output 8
PWM Output 1
Do not connect
Description
UART Data In
Power supply
Ground
Pin 10
Pin 1
7
Pin 20
Pin 11