X24-019WNC Digi International/Maxstream, X24-019WNC Datasheet - Page 28

• Manufacturer Part Number: X24-019WNC
• Description: MOD RF 2.4GHZ 19.2K W/WIRE ANT
• Manufacturer: Digi International/Maxstream

Specifications of X24-019WNC

• Frequency: 2.4GHz
• Data Rate - Maximum: 19.2kbps
• Modulation Or Protocol: FSK
• Power - Output: 17dBm
• Sensitivity: -110dBm
• Voltage - Supply: 5V
• Current - Receiving: 80mA
• Current - Transmitting: 150mA
• Data Interface: PCB, Through Hole
• Antenna Connector: On-Board, Wire Antenna
• Operating Temperature: 0°C ~ 70°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Applications: -
• Memory Size: -

XStream™ OEM RF Module – Product Manual v5.x00 [2006.02.24]
MY (Source Address) Command
NB (Parity) Command
PC (Power-up Mode) Command
PK (RF Packet Size) Command
<Networking & Security> Set/Read the source
address of the module.
Refer to the Addressing section [p36] of the RF
Communication Modes chapter for more
information.
<Serial Interfacing> Select/Read parity settings
for UART communications.
<Command Mode Options> PC Command allows
the module to power-up directly into AT
Command Mode from reset or power-on. If PC
Command is enabled with SM Parameter set to 1,
DI3 (pin 2) can be used to enter the module into
AT Command Mode. When the DI3 pin is de-
asserted (low), the module will wake-up in AT
Command Mode. This behavior allows module
DTR emulation.
<Serial Interfacing> Set/Read the maximum size
of the RF packets sent out a transmitting
module. The maximum packet size can be used
along with the RB and RO parameters to
implicitly set the channel dwell time.
Changes to this parameter may have a
secondary effect on the RB (Packet Control
Characters) parameter. RB must always be less
than or equal to PK. If PK is changed to a value
less than the current value of RB, RB is automatically lowered to be equal to PK.
© 2006 MaxStream, Inc. Confidential and Proprietary
AT Command: ATMY
Binary Command: 0x2A (42 decimal)
Parameter Range: 0 – 0xFFFF
Default Parameter Value: 0xFFFF (Disabled –
the DT (Destination Address) parameter serves
as both source and destination address.)
Number of bytes returned: 2
Related Commands: DT (Destination Address),
HP (Hopping Channel), ID (Modem VID), MK
(Address Mask), AM (Auto-set MY)
Minimum Firmware Version Required: 4.30
AT Command: ATPK
Binary Command: 0x29 (41 decimal)
Parameter Range: 0 – 0x100 [Bytes]
Default Parameter Value: 0x40 (64 decimal)
Number of bytes returned: 2
Related Commands: RB (Packetization
Threshold), RO (Packetization Timeout)
Minimum Firmware Version Required: 4.30
AT Command: ATNB
Binary Command: 0x23 (35 decimal)
Parameter Range: 0 – 5
Default Parameter Value: 0
Number of bytes returned: 1
Minimum Firmware Version Required: 4.30
(previous versions did not support the 9
AT Command: ATPC
Binary Command: 0x1E (30 decimal)
Parameter Range: 0 – 1
Default Parameter Value: 0
Number of bytes returned: 1
Minimum Firmware Version Required: 4.22
Parameter
Parameter
0
1
2
3
4
5
0
1
Power-up to Idle Mode
AT Command Mode
8-bit (no parity or
7-bit (any parity)
Configuration
Configuration
Power-up to
8-bit space
8-bit mark
8-bit even
8-bit odd
9-bit
th
28
bit.