DP1203C4333LF Semtech, DP1203C4333LF Datasheet
DP1203C4333LF
Specifications of DP1203C4333LF
Related parts for DP1203C4333LF
DP1203C4333LF Summary of contents
Page 1
... Data rate up to 152.3 kbit/s • Current consumption Tx=62 mA at15 dBm • Current consumption Rx=14 mA • Digital RSSI (Received Signal Strength Indicator) • Digital FEI (Frequency Error Indicator) DEVICE OPTIONS Part Number DP1203C4333LF DP1203C8683LF DP1203C9153LF 1 DP1203F Frequency band Package 433-435 MHz Board 868-870 MHz Board ...
Page 2
... Specifications ................................................................................................................................................5 3 Functional Description ...............................................................................................................................6 4 Serial Control Interface...............................................................................................................................7 5 Operation Modes .........................................................................................................................................8 5.1 Standard sequence for switching between receiver and transmitter ............................................................9 6 Typical Application ...................................................................................................................................10 7 Mechanical Dimensions............................................................................................................................11 8 Packaging Information..............................................................................................................................12 9 References .................................................................................................................................................12 © Semtech 2006 433/868/915 MHz RF Modules Table of Contents 2 DP1203F www.semtech.com ...
Page 3
... GND 11 GND 12 SO OUT SCK 15 CLKOUT OUT 16 DCLK OUT 17 DATA IN/OUT 18 DATAIN 19 PATTERN OUT © Semtech 2006 433/868/915 MHz RF Modules XE1203F 30.5 DESCRIPTION IN Ground RF input / output terminal Ground Supply voltage / Advised NC Supply voltage Ground Supply voltage IN 3-wire interface communication enable signal ...
Page 4
... Precaution should be taken when handling the device in order to prevent permanent damage Life Support Policy and Use in Safety Critical Applications SEMTECH PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF SEMTECH PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE UNDERTAKEN SOLELY AT THE CUSTOMER’ ...
Page 5
... The table below gives the specifications of the DP1203F under the following conditions: Supply Voltage VDD = 3.3V, temperature = 25 for DP1203C4333LF 869 MHz for DP1203C8683LF and fc = 915 MHz for DP1203C9153LF, frequency deviation ∆ kHz, bit rate BR = 4.8kbps, Base band filter bandwidth BBW = 200 KHz, bit error rate BER = 0.1 % (measured at the output of the bit synchronizer), antenna output matched at 50 Ω ...
Page 6
... The True RF DP1203F is a cost effective high performance radio transceiver module designed for the wireless transmission of digital information over distances of >500 meters in free space. The module is based on the RF transceiver circuit from SEMTECH, the XE1203F. For more information on the XE1203F, please refer to the XE1203F datasheet. ...
Page 7
... A(4) A(3) A(2) A(1) A(0) D(7) D(6) D(5) D(4) D(3) si /en so Write sequence into configuration register sck A(4) A(3) A(2) A(1) si /en so High impedance © Semtech 2006 433/868/915 MHz RF Modules High impedance A(0) D(7) D(6) D(5) D(4) D(3) Read sequence of configuration register 7 DP1203F D(2) D(1) D(0) D(2) D(1) ...
Page 8
... ConfigSwitch, SWITCH pin and SWParam Configuration Register For more information about the modes of operation, please refer to the XE1203F Datasheet. © Semtech 2006 433/868/915 MHz RF Modules RTParam_switch_ext SWParam configuration configuration parameter set selected 0 Set #1: ...
Page 9
... The drop-in module DP1203F is able to switch between any configuration by using the 3-wire bus or by using the pin SWITCH. This section describes the switching sequence from Set #1 to Set #2. Switching sequence by using the 3-wire bus RTParam_switch_ext = 0 Switching sequence by pad SWITCH RTParam_switch_ext = 1 © Semtech 2006 433/868/915 MHz RF Modules 9 DP1203F www.semtech.com ...
Page 10
... TYPICAL APPLICATION The schematic below shows the DP1203F interfaced with a SEMTECH’s microcontroller XE8806A PATTERN SAW PA match RF Switch GND RF IN/OUT GND VCC 82 nH 1nF © Semtech 2006 433/868/915 MHz RF Modules DATAIN CLKOUT DATA DCLK SCK SI SO GND LNA match Xtal XE1203F ...
Page 11
... MECHANICAL DIMENSIONS The following diagram shows the physical footprint and dimensions of the DP1203F drop-in module, which should be implemented on the mother board. 3.27 2.54 2.54 2. 10.89 © Semtech 2006 433/868/915 MHz RF Modules Top view 2.54 2.54 2.54 2.54 2.54 2.54 2.54 1. XE1203F ...
Page 12
... PACKAGING INFORMATION 9 REFERENCES - The XE1203F and the XE8806A datasheets, as well as the TN8000.18 Technical Note (XE8000 driving XE1200 transceivers standard API definitions) are available from Semtech website (www.semtech.com). © Semtech 2006 433/868/915 MHz RF Modules 12 DP1203F www.semtech.com ...
Page 13
... CUSTOMER’S OWN RISK. Should a customer purchase or use Semtech products for any such unauthorized application, the customer shall indemnify and hold Semtech and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs damages and attorney fees which could arise. ...