CYWM6935PAEC Cypress Semiconductor Corp, CYWM6935PAEC Datasheet - Page 5

• Manufacturer Part Number: CYWM6935PAEC
• Description: MODULE WIRELESS USB LR
• Manufacturer: Cypress Semiconductor Corp

Specifications of CYWM6935PAEC

• Frequency: 2.4GHz
• Data Rate - Maximum: 62.5kbps
• Modulation Or Protocol: GFSK
• Applications: AMR, ISM, RKE
• Power - Output: -16dBm
• Sensitivity: -95dBm
• Voltage - Supply: 3 V ~ 3.6 V
• Data Interface: Connector, 2 x 6 Header, 2mm Pitch
• Package / Case: Module
• Peak Reflow Compatible (260 C): No
• Supply Voltage: 3.3V
• Internal Oscillator Frequency: 24MHz
• Supply Voltage Max: 3.6V
• No. Of Bits: 8 Bit
• Data Rate Max: 62.5Kbps
• Leaded Process Compatible: No
• No. Of Pins: 28
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• Operating Temperature: -
• Memory Size: -
• Antenna Connector: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• Other names: 428-2020; CYWM6935PAEC

Document #: 001-07822 Rev. **
4.0
The CYWM6935PAEC Radio Module is a device that
transmits and receives radio signals in accordance with the
spectrum regulations for the 2.4-GHz unlicensed frequency
range. Regional regulatory agency approval may be required
to operate CYWM6935PAEC throughout the world.
Cypress Semiconductor Corporation has obtained regulatory
approvals for the CYWM6935PAEC to be used in specific
countries. CYWM6935PAEC was approved under the
“Modular Approval (MA) to the OEM.
The MA Grant provides that device manufacturers who incor-
porate CYWM6935PAEC as tested and approved can be
relieved from having to perform the Radio Regulatory certifi-
cation portion of the respective agency certification.
The MA Grant is valid only in countries
MA Grant certification process; the USA, Canada, Belgium,
Denmark, France, Finland, Germany, Italy, Netherlands,
Spain, Sweden, UK.
4.1
ule Approval
In order to be able to take advantage of Cypress’s modular
certification in an end product, the following must be ensured:
4.1.1
There
CYWM6935PAEC modules. The application types are defined
below:
Module is in a permanent location and has at least 2m
separation from the human body.
Module can be relocated and will have at least 20 cm
separation from the human body.
4.1.2
Note: Sidestepping these requirements is possible with
additional testing and/or recertification. However, modular
approval would no longer apply.
1. Correct Application.
2. Correct Installation.
3. Correct labeling.
— Modules cannot be modified in any way.
— Modules must be used only in the operating range spec-
— Modules cannot be located within 20 cm of another in-
— It is recommended to use Antenna-A or equivalent. The
— Must guarantee that end user cannot easily change an-
a. Fixed Application:
b. Mobile Application:
ified in the data sheets.
tentional radiator in the system.
antenna gain and form factor should be equivalent to
Antenna-A.
tenna.
are
Eligibility Requirements for Regulatory Mod-
Correct Application:
Correct Installation:
Module Certification Detail
two
types of application considered
[1.]
that recognize the
PRELIMINARY
for
4.1.3
If an end device containing a WirelessUSB CYWM6935PAEC
Radio Module will be sold or used in the USA, the enclosure
of the product must display a label with the following basic
elements:
If an end device containing a WirelessUSB CYWM6935PAEC
Radio Module will be sold or used in Europe, the enclosure of
the product must display a label with the following basic
elements:
If an end device containing WirelessUSB CYWM6935PAEC
Radio Module will be sold or used in Canada, the enclosure of
the product must display a label with the following basic
elements:
As of March 2006, Japan does not recognize the “Modular
Approval” certification. Regulatory certification for Japan
(TELEC) must be acquired through typical approval proce-
dures. These approvals are the sole responsibility of the OEM.
Note: Even with modular approval, the end device still has to
be tested for digital emissions compliance with all agencies as
an electronic device. The modular approval only eliminates the
need to test for compliance on RF transmissions.
4.2
Electronic device manufacturers using Cypress’s Modular
Approval are required to follow the below mentioned labeling
practice on the container in which the device is marketed or in
the product user’s guide. This should be in accompaniment
with other regulatory information. The text may be disbursed
according to language or geographic regions if desired, but the
exact text shown below must be maintained.
4.2.1
The device shall bear the following statement in a conspicuous
location:
This product contains Cypress WirelessUSB module
This product contains Cypress WirelessUSB module
Canadian Cert No IC: 5125A-UGWN2US
Canadian Cert No IC: 5125A-UGWN2US
Contains FCC ID: R8KUGWN2USHN33
Contains FCC ID: R8KUGWN2USHN33
Contains FCC ID: R8KUGWN2USHN33
Correct Labeling:
User Guide Information
United States of America requirements:
0122
0122
CYWM6935PAEC
Page 5 of 10
[+] Feedback