CNB10112 Panasonic - SSG, CNB10112 Datasheet
CNB10112
Specifications of CNB10112
Available stocks
Related parts for CNB10112
CNB10112 Summary of contents
Page 1
Specification 品種名/Type Number:CNB10112 種別/Type 反射型フォトセンサ/Reflective Photo Sensor 用途/Application 物体検知、無接点スイッチ/Object Detection、 Contactless SW. GaAs赤外発光ダイオード(非干渉性)・Siフォトトランジスタ 構造/Structure GaAs Infrared Light Emitting Diode (Non-Interference) ・NPN Si Photo Transistor 接続/Connection 附図/Attached 外形/Outline 絶対最大定格 Absolute Maximum 6 Ratings V 電気的・光学的特性/Electrical-Optical Characteristics 略号 項目/Item ...
Page 2
Specification 品種名/Type Number:CNB10112 (注 3)(Note3) 応答時間測定回路/Switching Time Measuring Circuit. Al 蒸着面/ Evaporated Al Sig IN 50 Ω (注 4)(Note4)入出力は電気によって行われます。/Input and output are practiced by electricity. (注 5) 本製品は、耐放射線を考慮した設計ではありません。 (Note5)This device is designed by disregarding for radiation. 2005-02-02 Established ガラス板/Glass ...
Page 3
Specification 外形図/Outline 品種名/Type Number:CNB10112 【外形図/Outline Drawing】 0.577 1.285 2.9±0.1 1.45 0.7 1.4 2005-02-02 Established 項目/Item リ−ド材質/ Pin Material C0.3 リ−ド処理/ Pin Process モ−ルド材質/ Mold Material 0.748 1.325 4−0.5 (注 1) 指示無き寸法公差は±0.2 (Note1) Not appointment tolerance :±0.2. Revised Semiconductor Company, ...
Page 4
Specification 外形図/Outline 品種名/Type Number:CNB10112 【パッケ−ジ裏面表示仕様/Package back display specification】 (注 1) パッケ−ジ裏面には上記種類のマ−ク表示品が混載します。 (Note1) The mark table article of the upper kind mixes in the package back. (注 2) マ−クは、目視又は顕微鏡に於いて解読できる事。 (Note2) What a date code sees an attention and can decode ...
Page 5
Specification 取扱い上の注意事項/Caution for Handling 品種名/Type Number:CNB10112 [はんだ付 け/Soldering] 1)手 はんだ付 け/Iron Soldering ・コテ先 温 度 300 ℃以 下 (はんだ温 度 目 安 :270 ℃以 下 )、2 秒 以 内 で使 用 して下 さい。 上 記 条 件 を超 えての使 ...
Page 6
Specification 取扱い上の注意事項/Caution for Handling 品種名/Type Number:CNB10112 [その他 ]/[Other] ・樹 脂 封 止 部 に触 ったり、外 力 を加 えないでください。 ・Please don’t touch parts of mold resin and don’t give stress. ・Auワイヤ−が透 けて見 えることがあります。 ・It is possible that Au wire is ...
Page 7
... This standard should be applied to the specifications of taping for CNB10112. [2]構造/Structure 1) 構 ...
Page 8
Specification テ−ピング仕様/Taping Specification 品種名/Type Number:CNB10112 [3]数量及び包装表示/Quantity and indication on the package. 1)テーピング数量/Taping quantity 3000 個/1 巻を標準装着数量とします。 The standard quantity shall be 3 000 pcs/reel. 3 巻を所定のカートンに梱包します。 3 reels shall be packed in the specified carton box. 2)表示/Indication リールに品名・数量・製造番号(略番号)を記載します。 The ...
Page 9
Specification テ−ピング仕様/Taping Specification 品種名/Type Number:CNB10112 [5]テープ形状及び寸法/Taping form and Dimensions ①キャリアテ−プ/Carrier tape ②カバ−テ−プ/Cover tape 項目 Item 縦/Length 製品挿入凹み角穴 横/Width Dented square 深さ/Depth hole for product insertion ピッチ/Pitch 直径/Diameter 送り穴 ピッチ/Pitch Sprocket hole 位置/Position 中心線間距離 縦方向/Longitudinal Center-to-center 横方向/Traverse distance カバ−テ−プ 幅/Width ...
Page 10
Specification テ−ピング仕様/Taping Specification 品種名/Type Number:CNB10112 [6]リ−ル及び寸法/Reel and Dimensions 表側 Surface 裏側 Back 項 直径/Diameter フランジ リ−ルの内側幅/Inner width of flanges Flange リ−ルの全幅/Outer width of flanges 外周直径/Outer diameter ハブ スピンドル穴の直径/Spindle hole diameter Hub キ−溝 Keyway 材質/Material 品名等の表示 Indication of the name ...
Page 11
Specification 信頼性保証基準/Reliability Guarantee Criterion 故障判定基準/Failure Criterion 品種名/Type Number:CNB10112 信頼性保証基準は、(MIL-STD-19500H LTPD:15 %)です。/ Reliability Guarantee Criterion(MIL-STD-19500H LTPD 15 %) 項 目/Item 実用動作試験/Operating Test 高温高湿動作試験/Temperature Humidity Operating Test 高温バイアス(BT)試験/High Temperature Bias Operating Life Test 高温高湿バイアス(THB)試験/Temperature Humidity Bias Operating Life Test 高温高湿保存試験/High Temperature ...
Page 12
... Reel 18 000 pcs カ-トン×2 箱/2 Carton 〔CNB10112〕 Revised Semiconductor Company, Matsushita Electric Industrial Co.,Ltd. シリカゲル Cilicagel Label 単位/Unit:mm ラベル貼付位置 ...
Page 13
Specification 品種名/Type Number:CNB10112 [製 品 保 管 /Storage] ・製 品 の搬 送 中 及 び保 管 中 の吸 湿 を避 けるため、シリカゲル入 りのアルミラミネート袋 による防 湿 包 装 を行 っております。 ・To prevent humid absorption while transporting or storing the product, humidity ...
Page 14
Specification 品種名/Type Number:CNB10112 《推奨パタ−ン寸法/Recommendable pattern dimension on reflow soldering》 0.9 1.1 (注意/Note) ・ここに記載されているパタ−ン寸法及び角穴寸法はあくまでも標準的な例であり、ご使用になる プリント基板や自動実装機の精度及びはんだ付け装置などの状況に応じてパタ−ン設計される ことをお勧め致します。 ・The pattern size and the corner hole size which is carried on this place are a standard size. It recommends that a pattern is ...