MG1-3000-A-9V-R SSI Technologies Inc, MG1-3000-A-9V-R Datasheet - Page 3

• Manufacturer Part Number: MG1-3000-A-9V-R
• Description: SENSOR DIGITAL GAUGE 3000PSI LCD
• Manufacturer: SSI Technologies Inc
• Series: MG-9Vr

Specifications of MG1-3000-A-9V-R

• Pressure Type: Gauge
• Operating Pressure: 3000 PSI
• Port Size: Male, 1/4" (6.35mm) NPT
• Output: LCD Display
• Accuracy: ±0.25%
• Voltage - Supply: 9V
• Operating Temperature: -10°C ~ 60°C
• Package / Case: Stainless Steel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 734-1157; MG1-3000-A-9V-000-000

Since piezo resistive pressure sensors are sensitive to
changes in temperature, the MediaGauge™ MG1-9V uses
signal conditioning to compensate for temperature and
calibration. The output signal is then converted into one of 3
user selectable forms (select units with the ON/UNIT/OFF
button):
The MediaGauge™ MG1-9V will display the pressure
reading after the ON/UNIT/OFF button is depressed. The
pressure measurement reading is updated 3 times per
second.
MediaGauge™ MG1-9V Panel
MediaGauge™ MG1-9V panel has a LCD display and three multi-
functional buttons – ON/UNIT/OFF; LIGHT/P-H (Peak-Held) and
RESET/CLEAR.
The
reading; switch between pressure units (PSI; BAR; and MPA) and
to power down the unit.
To power on the unit:
MediaGauge™ MG1-9V has a battery saver mode and will
automatically shut off the display after 3 minutes.
To display the pressure reading in a different pressure unit:
Continue to depress the ON/UNIT/OFF button until the arrow in
the LCD points to the pressure units desired.
SSI TECHNOLOGIES, INC.
Controls Division
2643 West Court Street
Janesville, WI 53548-5011
Phone: [phone]
Fax: [phone]
1) PSI
2) BAR
3) MPA (kg/cm²)
ON/UNIT/OFF button
MediaGauge™ (Model MG1-9V) Digital Pressure Gauge
SSI Technologies – Application Note PS-AN6
Press the ON/UNIT/OFF button.
is used to display the pressure
Product Overview
The
3
To manually power down the unit:
button and hold down for 3 seconds until OFF is displayed and
then release the button.
The
backlight on/off and to display the maximum peak pressure the
unit has measured.
To turn the LCD backlight on:
To turn the LCD backlight off:
again.
To see the maximum peak pressure the unit has measured:
Press and hold down the LIGHT/P-H button for 3 seconds. The
maximum pressure reading will be blinking.
pressure read was over the unit’s maximum pressure range, o.L
will be blinking on the display.
To return to the current pressure reading:
button and hold down for 3 seconds.
The
whatever pressure is currently applied to the port and to clear the
stored
RESET/CLEAR button only functions when held down for 3
seconds.
To reference your MediaGauge™ digital pressure gauge to the
input port:
seconds. The MediaGauge™ MG1-9V will now be reference to
your input port. For example, if you have 20 psi on the display and
then you press and hold the RESET/CLEAR button for 3 seconds
the display will show 0.0 psi. A measurement of 30 psi would then
read as 10 psi on the display.
LIGHT/P-H (Peak-Hold) button
RESET/CLEAR button
maximum
Press and hold the RESET/CLEAR button for 3
peak
pressure
Press the LIGHT/P-H button once.
is used to reset the gauge to
Copyright November 6, 2008
SSI Technologies Inc.
Press the LIGHT/P-H button
All Rights Reserved
reading.
Revision 3
Press the ON/UNIT/OFF
is used to turn the LCD
Press the LIGHT/P-H
If the maximum
Note:
The