SD-2131 Copal Electronics Inc, SD-2131 Datasheet - Page 3

• Manufacturer Part Number: SD-2131
• Description: SWITCH ROTARY BCD 10-POS SIDE
• Manufacturer: Copal Electronics Inc
• Series: SD-2000r

Specifications of SD-2131

• Circuit: BCD Complement
• Number Of Positions: 10
• Contact Rating @ Voltage: 0.1A @ 5VDC
• Actuator Type: Rotary with Shaft
• Actuator Level: Raised
• Mounting Type: Through Hole
• Orientation: Side Actuated
• Washable: No
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 563-1076

Reflow profile for soldering heat evaluation
Circuit type
Operating temperature range
Storage temperature range
Sealing
Net weight
Vibration
Shock
Humidity (Steady state)
Load life
High temperature exposure
Low temperature exposure
Thermal shock
Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request.
STANDARD SPECIFICATIONS
ENVIRONMENTAL CHARACTERISTICS
250
200
150
100
( C)
50
180 C
150 C
Reflow : two times maximum
Pre Heating Zone
Without knob Top setting 0.65 g
With knob Top setting 0.76 g
Without knob Side setting 0.95 g
With knob Side setting 1.05 g
Peak : 250
Heating time
10-500-10 Hz, 3 directions for 2 h each
BCD (Real code, complementary code)
BCH (Real code, complementary code)
40 °C, Relative humidity 90 ~ 95 %, 240 h
Over 230 C
25 (0.5 h) ~ 85 °C ( 0.5 h ), 5 cycles
90 30 s
6 directions for 3 times each
30 10 s
Amplitude 1.5 mm or
Acceleration 98 m/s
+5
0
490 m/s
DC5 V, 100 mA
Non washable
20000 steps
C
85 °C, 96 h
25 °C, 96 h
25 ~ 85 °C
Soldering Zone
2
, 11 ms
2
,
Contact rating
Contact resistance
Insulation resistance
Dielectric strength
No. of positions
Adjustment torque
Stepping angle
Terminal strength (Through hole pin only)
Stop strength (With knob only)
Solderability
Soldering
heat
Shear (Gull wing only)
Substrate bending (Gull wing only)
Pull-off strength (Gull wing only)
Non-switching
Switching
Minimum
ELECTRICAL CHARACTERISTICS
MECHANICAL CHARACTERISTICS
Gull wing
Through
hole pin
ROTARY CODED SWITCHES
SD-1000/2000
COPAL ELECTRONICS
Reflow : Peak temperature 255 °C
(Please refer to the profile below.)
Manual soldering : 350
Flow : 260 3 °C as the temperature in
Manual soldering : 380
Width 90 mm, bend 3 mm, 5 s, 1 time
22.5° (SD-1000), 36° (SD-2000)
1000 M (DC100 V) minimum
4 ~ 25 mN·m {41 ~ 255 gf·cm}
16 (SD-1000), 10 (SD-2000)
a pot of molten solder, immer-
sion from head of terminal to
backside of board 5 ~ 6 s, two
times maximum
10 N {1.02 kgf} minimum
10 N {1.02 kgf}, 10 s
5 N {0.51 kgf}, 10 s
5 N {0.51 kgf}, 10 s
100 m maximum
245 3 °C, 2 ~ 3 s
DC50 V 100 mA
DC5 V 100 mA
DC20 mV 1 µA
AC250 V, 60 s
{ } : Reference only
10 °C, 3 ~ 4 s
10 °C, 3 ~ 4 s
2004
Oct,