E39-L69 Omron, E39-L69 Datasheet - Page 6

• Manufacturer Part Number: E39-L69
• Description: Industrial Photoelectric Sensors HORZ MTG BRACKT E3S
• Manufacturer: Omron
• Type: General Purpose Photoelectric Sensorr

Specifications of E39-L69

• Features: Control the laser with an Amplifier the same size as a Digital Fiber Amplifier
• Light Source: Infrared LED
• Connection: Prewired Cable
• Output Configuration: NPN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Sensor I/O Connectors
(Models with Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.)
(For M12, refer to XS5. For e-CON, contact your OMRON representative.)
Note: When using Through-beam models, order one connector for the Receiver and one for the Emitter.
Ratings and Specifications
* Values in parentheses indicate the minimum required distance between the Sensor and Reflector.
Sensing method
Sensing distance
Standard sensing object
Minimum detectable
object (typical)
Hysteresis (white paper)
Black/white error
Directional angle
Light source (wavelength)
Power supply voltage
Current consumption
Control output
Protection circuits
Response time
Ambient illumination
Ambient temperature range
Ambient humidity range
Insulation resistance
Dielectric strength
Vibration resistance
Shock resistance
Degree of protection
Connection method
Weight
Materials
Accessories
M12
(For -M1TJ
models)
e-CON
Size
Case
Display window Denatured polyarylate
Lens
Standard cable
Standard
Cable
E3T-ST1@
E3T-ST2@
Opaque, 2-mm dia. min.
2-mm dia opaque object
---
---
Emitter: 2° to 20°, Receiver: 2° to 70° Emitter: 3° to 25°, Receiver: 3° min.
Red LED (“Pin-point” LED) λ = 650 nm
12 to 24 VDC ±10%, ripple (p-p) 10% max.
30 mA max. (Emitter 10 mA max., Receiver 20 mA max.)
Load power supply voltage: 26.4 VDC max.
Load current: 50 mA max. (residual voltage: 2 V max. for load current of 10 to 50 mA, 1 V max. for load current of less than 10 mA)
Open-collector output
Light ON: E3T-@@@1 and E3T-@@@3
Power supply and control output reverse polarity protection
Output short-circuit protection
Operate or reset: 1 ms max.
Incandescent lamp: 5,000 lx max.,
Operating: −25 to 55°C
Operating: 35% to 85%
20 MΩ min. at 500 VDC
1,000 VAC, 50/60 Hz for 1 min
Destruction: 10 to 2,000 Hz, 1.5-mm double amplitude or 300 m/s
Destruction: 1,000 m/s
IP67 (IEC60529)
Pre-wired (standard length: 2 m)
Approx. 40 g
PBT (polybutylene terephthalate)
Denatured polyarylate
Instruction manual, Installation Phillips screws (Side-view Models: M2 × 14, Flat Models: M2 × 8), Nuts, Spring
washers, Flat washers, E39-R4 (E3T-SR4@ only), E39-R37-CA (E3T-SR4@-S only)
E3T-ST11
E3T-ST12
E3T-ST21
E3T-ST22
NPN
Straight
Connector on one end
Connector on both ends
Side-view
1 m
300 mm
Appearance
2
E3T-ST13
E3T-ST14
E3T-ST23
E3T-ST24
3 times each in X, Y, and Z directions
PNP
Through-beam
E3T-FT1@
E3T-FT2@
Opaque, 1.3-mm dia. min.
1.3-mm dia opaque object
Sunlight: 10,000 lx max.
Storage: −40 to 70°C (with no icing or condensation)
Storage: 35% to 95% (with no condensation)
E3T-FT11
E3T-FT12
E3T-FT21
E3T-FT22
Dark ON: E3T-@@@2 and E3T-@@@4
NPN
1.1 to 1.5 m
0.5 to 1 m
1.6 to 2 m
Flat
2 m
5 m
2 m
5 m
500 mm
300 mm
Cable type
E3T-FT13
E3T-FT14
E3T-FT23
E3T-FT24
PNP
2
for 0.5 hrs each in X, Y, and Z directions
4-wire
4-wire
E3T-SR4@
200 mm (30 mm) (Using the E39-R4)
100 mm (10 mm) (Using the E39-R37-CA)
Opaque, 27-mm dia. min.
2-mm dia.
(sensing distance of 100 mm)
2° to 20°
20 mA max.
Power supply and control output re-
verse polarity protection
Output short-circuit protection, Mutual
interference prevention
Approx. 20 g
Methacrylic resin
Retro-reflective (without M.S.R.
Replace @ with the cable length in
0.1-m increments.
E3T-SR41
E3T-SR42
NPN
XS5F-D421-D80-A
XS5F-D421-G80-A
E39-ECON2M
E39-ECON5M
E39-ECONW@M
Side-view
function)
Model
E3T-SR43
E3T-SR44
PNP
E3T
6