F1206SB2500V032T AEM, F1206SB2500V032T Datasheet - Page 4

• Manufacturer Part Number: F1206SB2500V032T
• Description: Fuses 1206 2.5A 32V
• Manufacturer: AEM

Specifications of F1206SB2500V032T

• Current Rating: 2.5 Amps
• Voltage Rating: 32 Volts
• Fuse Size / Group: 1206
• Termination Style: SMD/SMT
• Body Material: Glass Ceramic
• Dimensions: 3.2 mm L x 1.6 mm W
• Product: Surface Mount Fuse
• Interrupt Rating: 50 Amps
• Mounting Style: SMD/SMT
• Operating Temperature Range: - 55 C to + 125 C
• Resistance: 0.07 Ohms
• Fuse Type: Time Delay / Slow Blow
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

SolidMatrix
Specifications and descriptions in this literature are as accurate as known at the time of publish, but are subject to change without notice.
Product Identification:
(1) (2)
(1) Series code: F－Chip Fuse
(2) Size code: Standard EIA Chip Sizes
(3) Action code: FA －Fast Acting; SB －Slow Blow; HI －High Inrush; FF－Very Fast Acting; HA－High Current
(4) Current rating code: 1000 — 1000 mA ( For HA, 10－10A)
(5) Voltage rating code: V024 — 24 VDC
(6) Package code: T — Tape & Reel, B — Bulk
(7) Marking code: M－With marking (Optional)
Environmental Tests:
Electrical Specifications:
Clear-Time Characteristics: Same as specified on the Short Form Data Sheet
Insulation Resistance after Opening: 20,000 ohms typical when cleared with rated voltage applied. Fuse clearing under low
voltage conditions may result in lower after clearing insulation resistance values. (Note: Under normal fault conditions (low or rated
voltage conditions), AEM SolidMatrix fuses provide sufficient after clearing insulation resistance values for circuit protection.)
Current Carrying Capacity: 100% rated current at +25ºC ambient for 4 hours minimum when evaluated per MIL-PRF-23419
Interrupt Ratings: as specified in this catalog.
Fuse Selection and Temperature De-rating Guideline:
The ambient temperature affects the current carrying capacity of
fuses. When a fuse is operating at a temperature higher than 25
the fuse shall be “de-rated”.
To select a fuse from the catalog, the following rule may be followed:
Catalog Fuse Current Rating = Nominal Operating Current / 0.75 /
% De-rating at the maximum operating temperature.
Example: At maximum operating temperature of 65
90%. The nominal operating current is 4A. The current rating for fuse
selected from the catalog shall be:
4 / 0.75 / 90% = 5.9 or 6A.
F 0603 FA 1000 V024 T M
No.
1
2
3
4
5
6
7
8
9
Soldering heat resistance
Solderability
Thermal shock
Moisture resistance
Salt spray
Mechanical vibration
Mechanical shock
Terminal strength
Life
(3) (4)
Test
English website: www.aem-usa.com
(5) (6) (7)
®
Surface Mount Fuses
DCR change ≤ ±10%
No mechanical damage
Minimum 95% coverage
DCR change ≤ ±10%
No mechanical damage
DCR change ≤ ±15%
No excessive corrosion
DCR change ≤ ±10%
No excessive corrosion
DCR change ≤ ±10%
No mechanical damage
DCR change ≤ ±10%
No mechanical damage
voltage drop change shall be less
than ±20% of initial value
No mechanical damage
No electrical “opens” during testing
Requirement
o
C, % De-rating is
2000 hours at ambient temperature between
+20°C and +30°C
Chinese website: www.aemchina.com
One dip at 260°C for 60 sec.
One dip at 255°C for 5 sec.
100 cycles between -65°C and +125°C
10 cycles
48 hour exposure
0.4” D.A. or 30 G between 5 – 3000 Hz
1500 G, 0.5 ms, half-sine shocks
30 sec. hanging for 1206 (1.5kg) and 0603
(0.5kg), 2 lb pushing for 0402
80% rated current (75% for <1A fuses) for
o
C,
105
100
Test condition
95
90
85
80
75
70
65
60
55
50
45
40
35
30
25
20
15
10
5
0
-55
Temperature Effect on Current Rating
-35
Maximum Operating Temperature (
-15
5
25
45
MIL-STD-202
Method 210
MIL-STD-202
Method 208
MIL-STD-202
Method 107
MIL-STD-202
Method 106
MIL-STD-202
Method 101
MIL-STD-202
Method 204
MIL-STD-202
Method 213
Refer to AEM QIQ007
Refer to AEM QIQ106
65
Test reference
85
105
o
C)
Rev. Jun. 09
125
145