PCF1D220MCL1GS Nichicon, PCF1D220MCL1GS Datasheet
PCF1D220MCL1GS
Manufacturer Part Number
PCF1D220MCL1GS
Description
Aluminum Organic Polymer Capacitors 20volts 22uF SMD Polymer Solid
Manufacturer
Nichicon
Series
CFr
Datasheet
1.PCF1A331MCL1GS.pdf
(3 pages)
Specifications of PCF1D220MCL1GS
Esr
50 mOhms
Operating Temperature Range
- 55 C to + 105 C
Termination Style
SMD/SMT
Dimensions
6.3 mm Dia x 6 mm L
Dissipation Factor Df
0.12
Leakage Current
88 uAmps
Load Life
2000 Hrs
Product
Organic Polymer Aluminum - Chip Capacitors
Capacitance
22 uF
Tolerance
20 %
Voltage Rating
20 Volts
Ripple Current
1700 mAmps
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CF
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Tangent of loss angle (tan )
ESR (
Leakage Current (
Temperature Characteristics
(Max.Impedance Ratio)
Endurance
Damp Heat
(Steady State)
Resistance to
Soldering Heat
Marking
Series
Capacitance
Size
Item
Ultra Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at 260°C peak
correspondence.
Compliant to the RoHS directive (2002/95/EC).
Specifications
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
A
B
C
E
H
L
D
Dimension table in next page.
0.5 to 0.8
4
1)
4.0
5.4
5.0
4.3
4.3
1.0
5.5L
Voltage ( j:6.3v)
Lot No.
Chip Type, Standard
series
0.5 to 0.8
minutes at 105°C.
5
5.0
5.9
6.0
5.3
5.3
1.6
2)
6L
– 55 to +105°C
2.5 to 25V
3.3 to 1500µF
± 20%
Less than or equal to the specified value at 120Hz, 20°C
Less than or equal to the specified value at 100kHz, 20°C
Less than or equal to the specified value.
Z+105°C / Z+20°C
Z – 55°C / Z+20°C
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed
at right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface
shall not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall
be two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall
be once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
0.5 to 0.8
6.3
6.3
5.4
7.3
6.6
6.6
2.1
5.5L
Plastic platform
L
+0.1
- 0.4
at 120Hz, 20°C
0.5 to 0.8
6.3
0.3 MAX.
6.3
5.9
7.3
6.6
6.6
2.1
6L
0.8 to 1.1
8
1.25
1.25
8.0
6.9
9.0
8.3
8.3
3.2
7L
CS
C 0.2
0.8 to 1.1
H
(100kHz)
8
11.9
8.0
9.0
8.3
8.3
3.2
12L
Long Life
0.8 to 1.1
10
10.0
11.0
10.3
10.3
7.9
4.6
After 2 minutes' application of rated voltage at 20°C
Positive
Negative
8L
0.8 to 1.1
10
CF
Capacitance,
CG
10.0
11.0
10.3
10.3
Higher
9.9
4.6
Performance Characteristics
10L
0.8 to 1.1
10 12.7L
10.0
12.6
11.0
10.3
10.3
Type numbering system (Example : 6.3V 150µF)
4.6
P
1
(mm)
Low ESR
Capacitance change
tan
ESR
Leakage current (
Capacitance change
tan
ESR
Leakage current (
Capacitance change
tan
ESR
Leakage current (
C
2
F
3
(
(
(
0
4
1)
1)
1)
Voltage
CJ
J
5
Code
V
1
6
5
7
2)
2)
2)
1
8
2.5
e
Within ± 20% of the initial capacitance value (
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Within ± 20% of the initial capacitance value (
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Within ± 10% of the initial capacitance value (
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
M
9
Capacitance toleranc ( 20%)
Rated capacitance (150 F)
10
C
4
g
L
11
Rated voltage (6.3V)
12
1
6.3
j
Configuration
Series name
G
13
14
S
10
A
Type
CAT.8100Y
4 to 6.3 （ 5.5L）
5 to 10 （ L
16
C
D
20
D
6）
Taping code
Size code
Code
3)
3)
3)
GB
GS
25
E
Related parts for PCF1D220MCL1GS
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
PCF1D220MCL1GS Summary of contents
Page 1
... CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CF Chip Type, Standard series Ultra Low ESR, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2002/95/EC). Specifications Item – +105°C ...
Page 2
... CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CF series Standard Ratings Rated Voltage Surge Voltage Rated Capacitance (V)(code) ( 100 220 220 2.5 2.8 470 （0E） 820 1500 1500 33 100 100 150 150 150 4 4.6 220 （0G） 330 470 560 680 820 ...
Page 3
... PCF1C820MCL1GS 27 3300 PCF1C101MCL1GS 25 3500 PCF1C151MCL1GS 16 4400 PCF1C181MCL4GS 25 3600 PCF1C181MCL1GS 20 3900 PCF1C221MCL1GS 14 5050 PCF1C221MCL9GS 14 5000 PCF1C331MCL1GS 120 900 PCF1D100MCL1GS 50 1700 PCF1D220MCL4GB 50 1700 PCF1D220MCL1GS 45 2000 PCF1D390MCL1GS 45 2000 PCF1D470MCL1GS 40 2400 PCF1D560MCL1GS 40 2600 PCF1D680MCL1GS 40 2600 PCF1D820MCL1GS 22 3200 PCF1D101MCL1GS 35 2800 PCF1D121MCL1GS 20 4320 PCF1D151MCL1GS 80 1200 PCF1E6R8MCL1GS 60 1600 ...