C350C104K1G5TA Kemet, C350C104K1G5TA Datasheet - Page 7

• Manufacturer Part Number: C350C104K1G5TA
• Description: Multilayer Ceramic Capacitors (MLCC) - Leaded C350 0.1uF 100volts C0G 10%
• Manufacturer: Kemet
• Series: C350r

Specifications of C350C104K1G5TA

• Voltage Rating: 100 Volts
• Termination Style: Radial
• Operating Temperature Range: - 55 C to + 125 C
• Product: Conformally Coated MLCCs
• Dimensions: 5.08 mm W x 12.7 mm L x 14.22 mm H
• Dissipation Factor Df: 0.1
• Capacitance: 0.1 uF
• Tolerance: 10 %
• Temperature Coefficient: C0G (NP0)
• Lead Spacing: 10.16 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

10
GENERAL SPECIFICATIONS
ELECTRICAL
ENVIRONMENTAL
Working Voltage:
Axial (WVDC)
C0G
X7R
Z5U
Radial (WVDC)
C0G
X7R
Z5U
Temperature Characteristics:
C0G
X7R
Z5U
Capacitance Tolerance:
C0G
X7R
Z5U
Construction:
Epoxy encapsulated – meets flame test requirements
of UL Standard 94V-0.
High-temperature solder – meets EIA RS-198, Method 302,
Condition B (260°C for 10 seconds)
Lead Material:
Standard: 100% matte tin (Sn) with nickel (Ni) underplate
and steel core ( “TA” designation).
Alternative 1: 60% Tin (Sn)/40% Lead (Pb) finish with copper-
clad steel core ( “HA” designation).
Alternative 2: 60% Tin (Sn)/40% Lead (Pb) finish with 100%
copper core (available with “HA” termination code with c-spec)
Solderability:
EIA RS-198, Method 301, Solder Temperature: 230°C ±5°C.
Dwell time in solder = 7 ±
Terminal Strength:
EIA RS-198, Method 303, Condition A (2.2kg)
Capacitance @ 25°C:
Within specified tolerance and following test conditions.
C0G – 1000pF with 1.0 vrms @ 1 kHz
X7R – with 1.0 vrms @ 1 kHz (Referee Time: 1,000 hours)
Z5U – with 1.0 vrms @ 1 kHz
Dissipation Factor @25°C:
Same test conditions as capacitance.
C0G – 0.10% maximum
X7R – 2.5% maximum (3.5% for 25V)
Z5U – 4.0% maximum
Insulation Resistance @25°C:
EIA RS-198, Method 104, Condition A <1kV
C0G – 100 G
X7R – 100 G
Z5U – 10 G
Dielectric Withstanding Voltage:
EIA RS-198, Method 103
500V test @ 150% of rated voltage for 5 seconds
Vibration:
250V test @ 250% of rated voltage for 5 seconds
1000V test @ 120% of rated voltage for 5 seconds
with current limited to 50mA.
with current limited to 50mA.
with current limited to 50mA.
500V test @ rated voltage, >500V test @ 500V
500V test @ rated voltage, >500V test @ 500V
0 ±30 PPM / °C from -55°C to +125°C (1)
± 15% from -55°C to +125°C
+ 22%, -56% from +10°C to +85°C
±0.5pF, ±1%, ±2%, ±5%, ±10%, ±20%
±10%, ±20%, +80% / -20%
±20%, 80% / -20%
25, 50, 100, 200, 250
50, 100
25, 50, 100, 200, 250, 500, 1k, 1.5k, 2k, 2.5k, 3k
50, 100
1000pF with 1.0 vrms @ 1 MHz
50, 100, 200
50, 100, 200, 500, 1k, 1.5k, 2k, 2.5k, 3k
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, [phone]
or 1000 M
or 1000 M – F, whichever is less.
or 1000 M
– F, whichever is less.
– F, whichever is less.
seconds.
CERAMIC CONFORMALLY
ENVIRONMENTAL
(1) +53 PPM -30 PPM/ °C from +25°C to -55°C, + 60 PPM below 10pF.
(2) X7R and Z5U dielectrics exhibit aging characteristics; therefore, it is highly
recommended that capacitors be deaged for 2 hours at 150°C and stabilized
at room temperature for 48 hours before capacitance measurements are made.
>500V
Vibration:
EIA RS-198, Method 304, Condition D (10-2000Hz; 20g)
Shock:
EIA RS-198, Method 305, Condition I (100g)
Life Test:
EIA RS-198, Method 201, Condition D.
<200V
Post Test Limits @ 25°C are:
Capacitance Change:
C0G ( 200V) – ±3% or 0.25pF, whichever is greater.
C0G ( 500V) – ±3% or 0.50pF, whichever is greater.
X7R – ± 20% of initial value (2)
Z5U – ± 30% of initial value (2)
Dissipation Factor:
C0G – 0.10% maximum
X7R – 2.5% maximum (3.5% for 25V)
Z5U – 4.0% maximum
Insulation Resistance:
C0G – 10 G
X7R – 10 G
Z5U – 1 G
Moisture Resistance:
EIA RS-198, Method 204, Condition A (10 cycles
without applied voltage).
Post Test Limits @ 25°C are:
Capacitance Change:
C0G ( 200V) – ±3% or ±0.25pF, whichever is greater.
C0G ( 500V) – ±3% or ± 0.50pF, whichever is greater.
X7R – ± 20% of initial value (2)
Z5U – ± 30% of initial value (2)
Dissipation Factor:
C0G – 0.10% maximum
X7R – 2.5% maximum (3.5% for 25V)
Z5U – 4.0% maximum
Insulation Resistance:
C0G – 10 G
X7R – 10 G
Z5U – 1k M
Thermal Shock:
-55°C to 125°C); Condition A (Z5U: -55°C to 85°C)
C0G – 200% of rated voltage @ +125°C
C0G – rated voltage @ +125°C
X7R – 200% of rated voltage @ +125°C
Z5U – 200% of rated voltage @ +85°C
X7R – rated voltage @ +125°C
EIA RS-198, Method 202, Condition B (C0G & X7R:
with current limited to 50mA.
“AXIMAX”
>1kV tested @ 500V.
>1kV tested @ 500V.
500V test @ rated voltage, >500V test @ 500V.
500V test @ rated voltage, >500V test @ 500V.
or 100 M
or 100 M – F, whichever is less.
or 100 M – F, whichever is less.
or 100 M – F, whichever is less.
or 100 M
or 100 M
& GOLD MAX
– F, whichever is less.
COATED/AXIAL
– F, whichever is less.
– Fwhichever is less.