BLM21BB221SH1D Murata, BLM21BB221SH1D Datasheet - Page 56

• Manufacturer Part Number: BLM21BB221SH1D
• Description: EMI/RFI Suppressors & Ferrites 0805 220ohms HiSpeed Signal Line Tape
• Manufacturer: Murata
• Series: BLM Br

Specifications of BLM21BB221SH1D

• Shielding: Unshielded
• Test Frequency: 100 MHz
• Product: Chip Ferrite Beads
• Impedance: 220 Ohms
• Tolerance: 25 %
• Maximum Dc Current: 200 mAmps
• Maximum Dc Resistance: 0.35 Ohms
• Operating Temperature Range: - 55 C to + 125 C
• Package / Case: 0805 (2012 metric)
• Termination Style: SMD/SMT
• Dc Resistance Max: 0.35ohm
• Dc Current Rating: 200mA
• Ferrite Mounting: SMD
• Ferrite Case Style: 0805 / 2012
• Operating Temperature Max: +125°C
• Operating Temperature Min: -55°C
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
<Unless otherwise specified>
1. Electrical Performance
2. Mechanical Performance
54
No.
No.
Specifications and Test Methods
*1 DLW31S only.
*2 DLW43S only.
1
2
3
4
5
1
2
3
4
Test and Measurement Conditions
Temperature: Ordinary Temp. 15 to 35 C
Humidity: Ordinary Humidity 25 to 85% (RH)
Specifications
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Common Mode
Impedance (Zc)
Common Mode
Inductance (Lc)
Insulation
Resistance (I.R.)
Withstanding Voltage
DC Resistance
Appearance
and Dimensions
Solderability
Resistance to
Soldering Heat
Bonding Strength
Item
Item
*2
*1
Within the specified tolerance.
10M min.
Products should not be damaged.
Meet the initial value specification.
Meet dimensions.
The electrodes should be at least 90% covered with
new solder coating.
Meet Table 1, next page.
No evidence of coming off substrate.
Products should not be mechanically damaged.
Specifications
Specifications
<In case of doubt>
Temperature: 20 2 C
Humidity: 60 to 70% (RH)
Atmospheric Pressure: 86 to 106kPa
Measuring Equipment: Agilent 4291A or the equivalent
Measuring Frequency: 100 1MHz
Measuring Equipment: Agilent 4294A or the equivalent
Measuring Frequency: 1MHz or 0.1MHz (DLW43SH101XP2)
Measuring Voltage: Rated Voltage
Charging Time: 1 minute max.
Test Voltage: 2.5 times for Rated Voltage
Tsting Time: 1 to 5 s
Charge/Discharge Current: 1mA max.
Measuring Current: 10mA max.
(In case of doubt in the above mentioned standard conditions,
measure by 4 terminal methods.)
Visual Inspection and measured with micrometer.
Flux: Ethanol solution of rosin, 25wt% includes activator
equivalent to 0.06 to 0.10wt% chlorine
Pre-heating: 150 5 C, 60 5s
Solder: qSn/Pb=60/40
Solder Temperature: q230 5 C
Immersion Time: q3 0.5s
Immersion and emersion rates: 25mm/s
Flux: Ethanol solution of rosin, 25wt% includes activator
equipment to 0.06 to 0.10wt% chlorine
Pre-heating: 150 5 C, 60 5s
Solder: Sn/Pb=60/40 or Sn-3.0Ag-0.5Cu solder
Solder Temperature: 260 5 C
Immersion Time: 10 0.5s
Immersion and emersion rates: 25mm/s
Then measured after exposure in room condition for 4 to
48 hrs.
It should be soldered on the substrate.
Applying Force (F): 10N (DLW31S Series)
Applying Time: 5 1s (DLW31S Series)
wSn-3.0Ag-0.5Cu solder
60s (DLW43S Series)
w4 1s
Substrate
17.7N (DLW43S Series)
Stainless tweezers
w245 3 C
Test Methods
Test Methods
Continued on the following page.
Please hold product as shown.
Test board fixture
Pressure
Product
C50E.pdf
1
08.8.28