BLM18RK102SN1D Murata, BLM18RK102SN1D Datasheet - Page 177

• Manufacturer Part Number: BLM18RK102SN1D
• Description: EMI/RFI Suppressors & Ferrites 0603 1K OHM
• Manufacturer: Murata

Specifications of BLM18RK102SN1D

• Shielding: Unshielded
• Test Frequency: 100 MHz
• Product: Chip Ferrite Beads
• Impedance: 1 KOhms
• Tolerance: 25 %
• Maximum Dc Current: 200 mAmps
• Maximum Dc Resistance: 0.8 Ohms
• Operating Temperature Range: - 55 C to + 125 C
• Package / Case: 0603 (1608 metric)
• Termination Style: SMD/SMT
• Dc Resistance Max: 0.8ohm
• Dc Current Rating: 200mA
• Ferrite Mounting: SMD
• Ferrite Case Style: 0603
• Inductor Case Style: 0603
• No. Of Pins: 2
• Core Material: Ferrite
• Resistance: 0.8ohm
• Rohs Compliant: Yes
• Operating Temperature Min: -55°C
• Operating Temperature Max: +125°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
Chip Common Mode Choke Coil
1. Do not use products beyond the rated current and
2. Be sure to provide an appropriate fail-safe function on
1. Self-heating
<Operating Environment>
Do not use products in a chemical atmosphere such as
chlorine gas, acid or sulfide gas.
Do not use products in the environment close to the
organic solvent.
<Storage and Handling Requirements>
1. Storage Period
2. Storage Conditions
(1) Storage temperature: -10 to +40˚C
(2) Do not store products in a chemical atmosphere
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
rated voltage as this may create excessive heat and
deteriorate the insulation resistance.
your product to prevent a second damage that may be
caused by the abnormal function or the failure our
product.
Please provide special attention when mounting chip
common mode choke coils in close proximity to other
products that radiate heat.
The heat generated by other products may deteriorate
the insulation resistance and cause excessive heat in
this component.
PLT10H series should be used within 12 months.
Solderability should be checked if this period is
exceeded.
Rating
Soldering and Mounting
Storage and Operating Conditions
Relative humidity: 15 to 85%
Avoid sudden changes in temperature and humidity.
such as chlorine gas, acid or sulfide gas.
!Caution/Notice
!Caution
Notice
2. Mounting Direction
1. Cleaning
2. Soldering
3. Other
1. Handling of a Substrate
Bending
Mount Chip Common Mode Choke Coils in right
direction. Wrong direction, which is 90 degrees
rotated from right direction, causes not only open or
short circuit but also flames or other serious trouble.
Notice (Soldering and Mounting)
Failure and degradation of a product are caused by
the cleaning method. When you clean in conditions
that are not in mounting information, please contact
Murata engineering.
Reliability decreases with improper soldering methods.
Please solder by the standard soldering conditions
shown in mounting information.
Noise suppression levels resulting from Murata's EMI
suppression filters EMIFILr may vary, depending on
the circuits and ICs used, type of noise, mounting
pattern, mounting location, and other operating
conditions. Be sure to check and confirm in advance
the noise suppression effect of each filter, in actual
circuits, etc. before applying the filter in a commercial-
purpose equipment design.
Handling
After mounting products on a substrate, do not apply
any stress to the product caused by bending or
twisting to the substrate when cropping the substrate,
inserting and removing a connector from the substrate
or tightening screw to the substrate.
Excessive mechanical stress may cause cracking in
the Product.
right direction
Z
Twisting
wrong direction
Z
175
Mar.28,2011
C31E.pdf