PLY17BS1023R0A2B Murata, PLY17BS1023R0A2B Datasheet - Page 3

• Manufacturer Part Number: PLY17BS1023R0A2B
• Description: Common Mode Inductors 1mH 3A 250volt
• Manufacturer: Murata

Specifications of PLY17BS1023R0A2B

• Dimensions: 16 mm W x 18 mm L x 17.5 mm H
• Product: Chokes
• Inductance: 1 mH
• Maximum Dc Current: 3 Amps
• Maximum Dc Resistance: 100 mOhms
• Operating Temperature Range: - 25 C to + 120 C
• Termination Style: Through Hole
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

I Equivalent Circuit
I !Caution (Rating)
! Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
PLY17BS2921R2B2p
PLY17BS3721R0B2p
PLY17BS5620R8B2p
PLY17BS7820R7B2p
PLY17BS9320R6B2p
Operating Temperature Range (Ambient Temperature Range + Winding Temperature Rise): -25°C to 120°C
Winding Temperature Rise (at Rated Current) (max.): 60K
o
1. Rated Current
2. Inrush Current
If these conditions are exceeded, excessive heat may
cause fumes or permanent damage to the component,
or at worst cause ignition.
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
This data sheet is applied for AC Line Filters Hybrid Choke Coils used for General Electronics equipment for your design.
Operating current should not exceed the rated
value. Even if operating current is under the
rated value, adequate ventilation is required to
avoid excessive heat generated within the product
(choke coil) and from surrounding heat sources.
If exceeding these conditions, excessive heat may
cause fumes or permanent damage to the product.
Please ensure that product (choke coil) is
evaluated and confirmed against the specification
when it is mounted in your final assembled product.
-> Winding temperature should be less than
*As for FKOB series winding temperature should be
less than 95 degree C.
Maximum allowable temperature at the surface of
coil (ambient temperature + winding temperature
rise) is in accordance with each safety standard
applicable to final assembled product.
When the temperature at winding exceeds maximum
allowable temperature of safety standard, the
rated current should be derated.
Inrush current should not exceed 10 times rated
current within 1/4 cycle of 50/60Hz commercial
power line. Inrush current should be limited to a
minimum of 10 seconds after last inrush.
120 degree C.
Part Number
(1)
(4)
No polarity.
Common Mode Inductance (min.)
2.9mH
3.7mH
5.6mH
7.8mH
9.3mH
(2)
(3)
Noise Suppression Products/EMI Suppression Filters > AC Line Filters > Hybrid Choke Coils
http://www.murata.com/
Data Sheet
Normal Mode Inductance (min.)
I Packaging
I Notice (Soldering and Mounting)
I Notice (Other)
Magnetic Flux Leakage
Coil Humming Noise
Code
Choke coils generate small amounts of magnetic flux
leakage that may adversely affect equipment operation
according to component arrangement.
Testing should be completed on final assembly to
ensure equipment performance is not affected.
Magnetic flux generated between coil and core or
between the choke coil windings creates repulsive
power between the coil windings. This repulsive
power causes the coil winding to vibrate and create
a humming noise. The amount of hum produced by the
coil is proportionate to the amount of harmonic
distortion generated by the operating current. This
does not influence the electrical performance of
the coils, but it should be considered and tested
in actual circuit application.
M
B
140µH
180µH
280µH
390µH
460µH
Packaging
Magazine
Box
Rated Current
1.2A
1.0A
0.8A
0.7A
0.6A
Minimum Quantity
Rated Voltage
1920
1080
250Vac
250Vac
250Vac
250Vac
250Vac
2007.7.4
2