PV36W102C01B00 Murata, PV36W102C01B00 Datasheet - Page 17

• Manufacturer Part Number: PV36W102C01B00
• Description: Trimmer Resistors - Multi Turn 1.0Kohms 10mm Square 25turn
• Manufacturer: Murata

Specifications of PV36W102C01B00

• Resistance: 1 KOhms
• Power Rating: 0.5 Watt (1/2 Watt)
• Operating Temperature Range: - 55 C to + 125 C
• Element Type: Cermet
• Product: Multi-Turn Trimmer Potentiometers
• Tolerance: 10 %
• Number Of Turns: 25
• Taper: Linear
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2
!Note
!Note
1. Store in temperatures of -10 to +40 deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
3. The maximum input current to a trimmer
4. If the trimmer potentiometer is used in DC and high
1. Soldering
16
PVZ3/PVS3/PVA3 Series Notice
(1) Standard soldering condition
(2) Flow soldering is available for PVA3 series.
the power depending on the resistance value.
potentiometer should not exceed (P.R)^1/2 or the
maximum operating voltage, whichever is smaller.
potentiometer should not exceed (P/R)^1/2 or the
allowable wiper current, whichever is smaller.
humidity conditions, please connect wiper (#2) for
plus and resistive element (#1 or #3) for minus.
Notice (Operating and Storage Conditions)
relative humidity of 30-85%RH.
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
Notice (Rating)
(PVZ3 Series only)
Notice (Soldering and Mounting)
(a) Reflow soldering :
(b) Soldering iron:
*PVZ3A_A01 series
*PVZ3A_C01, PVZ3K_E01, PVZ3R_E01 series
*PVS3, PVA3 series
Before using other soldering conditions than
those listed above, please consult with Murata
factory representative prior to using. If the
soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature,
the trimmer potentiometer may deviate from the
specified characteristics.
For PVZ3 and PVS3, do not use flow
soldering method (dipping).
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
>Temperature of tip 260 deg. C max.
>Soldering time
>Diameter
>Wattage of iron
>Temperature of tip 360 deg. C max.
>Soldering time
>Diameter
>Wattage of iron
Refer to the standard temperature profile.
2mm max.
2mm max.
3 sec. max.
3 sec. max.
30W max.
30W max.
2. Mounting
(1) Corrosive gaseous atmosphere
(2) In liquid
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(3) The soldering iron should not come in contact
(4) Apply the appropriate amount of solder paste.
(1) Use our standard land dimension. Excessive land
(2) Do not apply excessive force (preferably 4.9N
(3) Do not warp and/or bend PC board to prevent
the following environmental conditions:
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
If you use the flow soldering method, the
trimmer potentiometer may not function.
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
The thickness of solder paste should be printed
from 150 micro m to 200 micro m (PVZ3 series
should be printed from 100 micro m to 150 micro m)
and the dimension of land pattern used should be
Murata's standard land pattern at reflow
soldering. Insufficient amounts of solder can
lead to insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals.
area causes displacement due to the effect of the
surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
(Ref.; 500gf) max.), when the trimmer
potentiometer is mounted to the PCB.
Continued on the following page.
R50E13.pdf 04.6.11