CM1412-03CP ON Semiconductor, CM1412-03CP Datasheet
CM1412-03CP
Specifications of CM1412-03CP
Available stocks
Related parts for CM1412-03CP
CM1412-03CP Summary of contents
Page 1
... EMI both to and from a microphone element. They also support AC signals, enabling audio signals to pass through without distortion. In addition, the CM1412 provides a very high level of protection for sensitive electronic components that may be subjected to electrostatic discharge (ESD). The input pins safely dissipate ESD strikes of the maximum requirement of the IEC 61000-4-2 international standard ...
Page 2
... Block Diagram PIN NAME DESCRIPTION A1 MIC_IN1 Microphone Input 1 (from microphone) A3 MIC_IN2 Microphone Input 2 (from microphone) B2 GND Device Ground C1 MIC_OUT1 Microphone Output 1 (to audio circuitry) C3 MIC_OUT2 Microphone Output 2 (to audio circuitry) PIN DESCRIPTIONS Rev Page www.onsemi.com CM1412 ...
Page 3
... PARAMETER Storage Temperature Range DC Power per Resistor DC Package Power Rating STANDARD OPERATING CONDITIONS PARAMETER Operating Temperature Range PART NUMBERING INFORMATION Package Ordering Part Number CSP CM1412-03CP ABSOLUTE MAXIMUM RATINGS Rev Page www.onsemi.com Lead-free Finish 1 Part Marking CB RATING UNITS -65 to +150 100 ...
Page 4
... Note 3: Clamping voltage is measured at the opposite side of the EMI filter to the ESD pin. For example, if ESD is applied to Pin A1, then clamping voltage is measured at Pin C1. Note 4: Unused pins are left open. CONDITIONS V =5. 10mA LOAD Notes 2 and 4 Notes 2,3 and 68Ω 47pF Rev Page www.onsemi.com CM1412 ) (NOTE 1 MIN TYP MAX UNITS Ω ...
Page 5
... CM1412 Performance Information Typical Filter Performance (nominal conditions unless specified otherwise, 50 Ohm Environment) Figure 1. Insertion Loss VS. Frequency (A1-C1 to GND B2) Figure 2. Insertion Loss VS. Frequency (A3-C3 to GND B2) Rev Page www.onsemi.com ...
Page 6
... Figure 6. Lead-free (SnAgCu) Solder Ball Reflow Profile N on-Solder M ask D efined Pad 0.240m m D IA. Solder Stencil Opening 0.300m m D IA. Solder Mask Opening 0.290m m D IA. Rev Page www.onsemi.com CM1412 VALUE 0.240mm Round Non-Solder Mask defined pads 0.290mm Round 0.125mm - 0.150mm 0.300mm Round 50/50 by volume ...
Page 7
... C2 0.575 0.644 0.714 0.0226 0.0254 0.0281 D1 0.368 0.419 0.470 0.0145 0.0165 0.0185 D2 3500 pieces # per tape and reel Controlling dimension: millimeters 5 Inches Min Nom Max Rev Page www.onsemi.com Package Dimensions for CM1412 Chip Scale Package ...
Page 8
... CSP Tape and Reel Specifications PART NUMBER CHIP SIZE (mm) CM1412 1.41 X 0.95 X 0.644 POCKET SIZE (mm) TAPE WIDTH 1.52 X 1.07 X 0.720 8mm Figure 5. Tape and Reel Mechanical Data Rev Page www.onsemi.com REEL QTY PER W DIAMETER REEL 178mm (7") 3500 CM1412 4mm 4mm ...
Page 9
... CM1412 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “ ...