ADT7301ARTZ-500RL7 Analog Devices Inc, ADT7301ARTZ-500RL7 Datasheet - Page 14

• Manufacturer Part Number: ADT7301ARTZ-500RL7
• Description: IC SENSOR TEMP 13BIT DGT SOT23-6
• Manufacturer: Analog Devices Inc

Specifications of ADT7301ARTZ-500RL7

• Function: Temp Monitoring System (Sensor)
• Topology: ADC, Register Bank
• Sensor Type: Internal
• Sensing Temperature: -40°C ~ 150°C
• Output Type: MICROWIRE™, QSPI™, SPI™
• Output Alarm: No
• Output Fan: No
• Voltage - Supply: 2.7 V ~ 5.25 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Package / Case: SOT-23-6
• Ic Output Type: Digital
• Sensing Accuracy Range: ± 0.5°C
• Supply Current: 1.6mA
• Supply Voltage Range: 2.7V To 5.25V
• Resolution (bits): 13bit
• Sensor Case Style: SOT-23
• No. Of Pins: 6
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADT7301EB - BOARD EVALUATION FOR ADT7301
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: Q2494841C

ADT7301
ADT7301-to-ADSP-21xx Interface
Figure 18 shows an interface between the ADT7301 and the
ADSP-21xx DSP processor. To ensure correct operation of the
interface, the SPORT control register should be set up as follows:
TFSW = RFSW = 1, alternate framing
INVRFS = INVTFS = 1, active low framing signal
DTYPE = 00, right justify data
SLEN = 1111, 16-bit data-words
ISCLK = 1, internal serial clock
TFSR = RFS = 1, frame every word
IRFS = 0, RFS configured as input
ITFS = 1, TFS configured as output
The interface requires an inverter between the SCLK line of the
ADSP-21xx and the SCLK input of the ADT7301. On the
ADSP-21xx interface, the TFS and RFS of the SPORT are tied
together; TFS is set as an output, and RFS is set as an input. The
DSP operates in alternate framing mode and the SPORT control
register is set up as described in this section.
*ADDITIONAL PINS OMITTED FOR CLARITY
ADT7301*
Figure 18. ADT7301-to-ADSP-21xx Interface
DOUT
SCLK
DIN
CS
SCK
DR
DT
RFS
TFS
ADSP-21xx*
Rev. A | Page 14 of 16
MOUNTING THE ADT7301
The ADT7301 can be used for surface or air temperature
sensing applications. If the device is cemented to a surface with
a thermally conductive adhesive, the die temperature will be
within about 0.1°C of the surface temperature because of the
ADT7301’s low power consumption. Care should be taken to
insulate the back and leads of the device if the ambient air
temperature is different from the surface temperature being
measured.
The ground pin provides the best thermal path to the die;
therefore, the temperature of the die is close to that of the
printed circuit ground track. Care should be taken to ensure
that this is in good thermal contact with the measured surface.
As in any IC, the ADT7301 and its associated wiring and
circuits must be kept free from moisture to prevent leakage and
corrosion, particularly in cold conditions where condensation is
more likely to occur. Water-resistant varnishes and conformal
coatings can be used for protection. The small size of the
ADT7301 allows it to be mounted inside sealed metal probes,
which provide a safe environment for the device.
SUPPLY DECOUPLING
The ADT7301 should be decoupled with a 0.1 μF ceramic
capacitor between V
if the ADT7301 mount is remote from the power supply.
DD
and GND. This is particularly important